Search results for query: *

Also, driver's door vin is JS which is an R/T challenger with U code 440, so looks like the door may be from another challenger. But still a nice car!

Sixth digit in vin is 0 for 1970?

If you were closer to east tn but the shipping would be to expensive for me.

Thanks!

Thanks, and if I'm not mistaken the rad core support has some numbers that should match the vin also, a friend said?

do any of the 4 speed numbers on the trans match the vin numbers on the dash of 72 duster

Having had several sure grips over the years, it acts as a peg leg under normal driving, then when ya gas on it pretty good the clutches grip or lock in under hard type accelerations and cause both wheels take hold or grip, giving better hole shots one could say, but (don't try it in turning...

Sorry, cleared.

Can I get pic of the vin also, thanks! tried to send private, not sure

Hey was this a 340 car to start with and has the rear end been shortened any? thanks Jimmy

hey just curious as to the brand or info on those heads on that engine, they look like some serious heads! thanks, JR

like this looks like one that should "live" darn...

asking 3,000 cut it up and get 700....? happens alot

Sorry for your engine troubles, don't worry about comments, just be patient and do the best ya can!

intake port pics, 318 size or 360 on these, thanks

Why do some R blocks have a 9.20 deck height and not the 9.59 height?

73Swinger18 is right make sure no. 1 piston is tdc on compression stroke not on exhaust stroke then make sure rotor is pointing to the plug wire going to no. one cyl.

Yes, I had a block full of jell like crud in a late 60s 318 that caused it to run hot also!

My 1994 5.2 Dodge B250 van would run cooler below about 50 mph but would start overheating at hwy speeds, tried cap thermostat. water pump and poured water into radiator with bottom hose off and water came out so i though the radiator was ok so finally i got a radiator off a van like mine and it...

Could have a couple of plug wires that may have mistakenly got crossed? I seen that do odd things to performance depending on which two are crossed!

There was a 67 dated 340 block for sale here on fabo about 5 months or so ago! I tried to buy a block on craigslist around 7 years ago in KY. The guy said it was 67 dated 340! But he backed out. So the story is the first ones were cast in 67 for use in upcoming 68 models.

Hey just checking , do the prototype heads have a small freeze plug in the ends of them? Thanks

When mine did that i could raise the hood and look down into the carb while working the throttle arm by hand and each time it stalled the carb was not squirting fuel so i knew it was in the fuel system, if it is pumping fuel then you can try a points distributor and bypass the electronic...

I had a 1970 Duster that would stall like that from time to time, it turned out to be the rubber gas line from the tank to the metal fuel line that runs along side of the underside to the fuel pump. The rubber hose from the tank was dry rotted and would sometimes suck air instead of gas and...

Your right about derby cars, i was thinking the same thing and the serious derby guy's have been known to pay $2,000 or more for just the old Chrysler body's!

Driving pass a junk yard in the inner city of Atlanta GA today and this rare gem was setting out front, i turned around and asked about if they were fixing it up or if it was for sale. They said someone had already bought it, so at least it was not headed to the scrap pile!

Yes it was, also it was probably a work truck at one time, 2wd, 8 lug.

1995 V10 truck motor/auto 2wd trans still in truck, just seen it today, know nothing about condition period. p.a.p in mobile al. Probably priced at $250 or so for engine. Hope its ok to post this as these are rare. Not mine. thanks fabo