Search results for query: *

I will take it. Sending PM.

Kingsley Automotive Machine in Nashua NH builds and races Mopars. Golen Engine is in Hudson NH. They build everything including Mopars, real nice shop. He built my friends 455 olds stroker and he has no problems with it. That motor has about 550 hp and over 600 ft lbs. of torque.

I have the same exact issue. I found this kit by SSBC which looks like it will solve the problem. They have two different lengths for the frame fitting. I have not measured the frame connectors to figure out which size to use yet. Stainless Steel Thru Frame Kit with nylon washers, Made in...

Here are Torsion bar part numbers and specs: 0.81 90#/in P5249148 drag bars 0.83 100#/in 2535888-9 slant six bars 0.85 110#/in 2535890-1 slant six w/air - 318 w/o air 0.87 120#/in P5249149 (2535892-3) 318 w/ air - 340 std bars 0.89 130#/in P5249150 383 std bars 0.92 150#/in p5249151 *h/d...

Price drop to $285 shipped.

Mopar 0.92 diameter torsion bars. Part number P5249151. These are new bars. They were mounted in the car for mock up but were never driven on. Changed direction on my build and no longer need them. Asking $300 shipped from Londonderry, NH.

New MSD distributor part number 8534. I did install this in my motor but it was never fired. I am running the Holley Sniper EFI and I’ve decided to run the Sniper hyper spark distributor. Asking $210 shipped from Londonderry NH. PayPal accepted.

Mopar Connection online magazine just did an article about restoring an a body console. It It was a good write up as they had to make some repairs to the console and they listed all of the part numbers for the products they used. They used SEM dye and SEM also makes a texture paint to match...

Qa1 single adjustable shocks - part number TS501. They have 18 levels of damping. These fit a bodies front shock. They are lightly used and are in great condition. These are $145 each new. Asking $200 for the pair shipped from Londonderry, NH.

Patriots 65

New Firm Feel 1.00 torsion bars. These are A Body torsion bars. Went in a different direction and never used these bars. $260 shipped in the USA from Londonderry, NH.

Sold pending payment.

Sold pending payment.

New Addco front sway bar kit, part number 150. Fits 67 - 72 a bodies. $125 shipped from Londonderry, NH.

New RMS Adjustable Upper Control Arms with Rod Ends. They fit 62 - 76 a bodies, but use the 73 and up big ball joint. These are new and have only been mounted for mock up. The tapered spacers are included but were not in the picture. Went in a different direction. Asking $275 shipped from...

New Four Speed Shifter Tunnel from AMD, part number 415-1067. Fits 67 - 74 a bodies. Do not need it and now it's collecting dust. Asking $110 shipped from Londonderry, NH.

Proform Distributor part number 66990. Fits small blocks. This distibutor was only used on the dyno to break in my engine which was built by MRL. I am using to efi so I switched to a MSD distributor as I do not need vacuum advance. $80 shipped from Londonderry, NH.

PST Steel Tie Rod Adjusters with Tie Rod Ends. These are the 11/16" adjusters, part number SAS440S. Inner and Outer Tie Rod part numbers are the same: TRE355L. These are new and have been installed for mock up only. Went in a different direction and no longer need these. These cost $150 from...

Magnumforce Stock Height Spindles never used, only mounted for mock up. They are based on the big bearing, big ball joint 73' and up spindle. I had them powder coated black. They no longer offer these, only the 2" drop spindle. Here is a link to the page, if you click on the stock spindle it...

QA1 Dynamic Strut Bars for a bodies, part number 52311. These are new and were only mounted for mock up. Went in a different direction. Asking $175 shipped from Londonderry, NH.

I had a discectomy on L5 S1 and then three years later I had a discectomy and laminotomy on S3 S4. It’s been about two and a half years since the last surgery. Both times I went from barely being able to walk because of the pain to 100% back to normal within six weeks of surgery. The pain was...

I have the freedom pet pass. Best dog door I have installed. Zero drafts and stays closed even with 50 mph+ wind gusts. Website is: The world's best pet doors | Freedom Pet Pass It wasn’t cheap, but it is worth it. My backyard is fenced so I’m not worried about other visitors coming in.

PM Sent

Patriots 55

This pump is rated at 120 gph at 6.9 to 9.5 psi. I would recommend running a pressure regulator with this pump.

Carter M6270 mechanical fuel pump. Fits small block la engines. Pump is almost new, was only used on the dyno during engine break in. I am using fuel injection so I don’t need this pump. $80 shipped from Londonderry, NH.

K Member has sold, pending payment.

I believe 68Dart500 is correct. You just have to use the biscuit style motor mounts.

QA1 K Member for 67 -72 a bodies, part number 52313. This has 0 miles on it. It was only installed for mock up. I decided to go to a full coilover conversion so this is for sale. There are a couple of chips in the powdercoat from handling/moving it during mock up. Asking $450 shipped from...

I recently bought the Moser stamped 8 3/4. It is based on the Ford 9" with a 489 case flange. I called Moser directly and they thought the stamped housing would be fine for my combo. I have a 408 stroker making 525 hp with a tko 5 speed. This is in a car that will be street driven 99% of the...