Search results for query: *

Ran fuel lines last night and checked out my trans cooler and controller wiring a bit last night. I love the PFTE stuff and the little compression fittings just like the stuff for copper plumbing and pecs. What a great product was so easy to use, I do need to find some heat wrap from the front...

Tail shaft mount nearly ready to install.

Final install of ZF 8HP70 for 1974 Dart Sport 360. Excited great easy morning. Did my angle check in degrees exactly as it was for stock setup. I will weld in my upper hoop now as it will no longer need to come in and out with new setup I made. The tunnel does not have to be huge but I'm...

Few test fits and changes to crossmember and upper hoop. Goes in this weekend. Then the plumbing and wiring and programming!

He had issues getting the exhaust routed but if your looking at other solutions here should be fine to start. My car dont have much left stock and big upgrade I am doing the ZF 8 speed in front of an old school LA360 build.

Look up Walker Induction solutions he has developed viable kits for twin turbos on the 3.6. I have seen the cars first hand they are amazing. Walker Induction Solutions

Adapter installed and the bushing. Looks like I will be using the .075 spacers for the torque converter. Torque to spec 55 foot pounds.

Ok upper hoop is in where I plan for it to live now. Minus any adjustments well stab transmission and build the tunnel around it. Three pieces top middle narrow side, should look way better than Ma Mopar did with her crooked weird tunnel. Great for stock of course but no reason to duplicate...

Now I can adjust the hoop little trim to do here and there but this should do it. I got back ordered trans mount puck, the 90 degree elbows for 10AN pfte trans lines, and a bushing thays supposed to be here today for the crank for the JVX flywheel install. If I can get this 40 bucks of parts...

Floor modification coming along nicely and the upper tunnel hoop will be wider and taller. This should give me plenty of room for new transmission. I also addressed the floor not being welded as it should be across the cross member corners.

A great looking truck! The 8HP70 LASB/rb page on Facebook ZF swaps may be of interest. Ram Charger with LA360 did the swap and he loves. Sounds like perfect candidate you got here. I am doing it on my Dart Sport right now.

So my issue with this system is it's for a Hemi swap and motor forward. I really don't like the idea of forcing more weight to front 3 inches. Hemi its long and bigger makes sense. But I'm using a JVX adapter 360 engine stays put and trans mount moves with torsion bars in place. Cost is a...

Ok here I am Getting ahead of Denny lol I should have just called you. Looks like I am on the right path OEM k frame I am using with the Hooker black heart and modify the hoop for the NAG 1 kit. I will keep sharing can't hurt but I may be calling you. Thanks!

Here is a picture of the Dodge shifter. Pretty standard on the console cars versus the turn dial. This flips over to side and then you shift like a manual it's 8 gears and ZF shift is 150ms. I doubt other than maybe a road course or parking lot fun/drag race that you would use this. I have...

Coming along let me explain what's about to happen here. 1. Trim the upper underside tunnel where firewall and floor meet. This hangs down about an inch gotta go. Weld that and grind smooth. 2. Lift tunnel up and out to accommodate the ZF. It's not a very big tunnel and we're talking about...

I did the standard shifter that has the ability to be shifted up or down in the stick. Still it was 580 shipped but it is all brand new. This is not a cheap swap not going there lol. It is reliable though and for what an auto can do not sure you could do much better for a new transmission and...

I purchased the Sound German Automotive controller 1032.00 delivered to door. Lots of cars have been completed with Russell Drake's unit with good results. These are daily drivers done at home in most cases. The Lamik unit is very very expensive and considering it's not turn key and requires...

Pulled the 727 trans tonight and will get new upper cross member hoop in and we'll see what else needs to be done to fit the ZF. I will take pictures of any mods as we do them. Idea here is keep torsion suspension can be done and fit the transmission and have the proper degree angle. I'll...

2nd frame connector is in the car. We're it not for taking out the old gas line would have been easy. I fabbed this one up in a couple hours. Lot cleaner than the first I think. I also itemized the cost for the total of ZF transmission kit. You could do it cheaper I didnt cheap out or part...

Nice which transmission cross member is that? I'm using the B body 8hp70 trans mount with a modified nag 1 cross member Blackheart unit but my transmission is farther forward due to 360 location. I did look at your mount style and motortrend did a write up using a Chevy style cross member...

Ok so I got curious and now I'm making these as well. I'm there and its in the air and I figure if it makes trans tunnel and torsion bar setup more stable why not! How to make torque boxes

One frame connector down and one to go. What a huge difference just closing door wow you tell shocked by that.

Did you use the Holley cross member upper hoop replacement. I'm taking out the upper factory one it's huge and in the way and trimming the lower part as well. I'm sure I need to cut some ears off transmission they stick way way up. Already seen that done on A body without removing entire...

I need to start thinking about a drive shaft plan. CV joint style 2020 Challenger RT style then needs a slip yoke, then will need a standard 1310 U joint on a 8 1/4 rear end. I ordered my shifter today not cheap the Challenger 8HP shifter and the knob itself 550 from Sound German Automotive. I...

Yeah I imagine the hemi sits further back closer to firewall. I don't plan to move my engine back using an adapter from LA block to 8hp70. I know it won't be perfect we'll see what happens.

Pictures sure would be cool I am doing an 8hp70 right now and won't be cutting up the entire tunnel only back half where Holley hoop goes in.

Once I have the Dart driving down the road I will have a list of parts used and prices. This is a cheaper option the ZF than a brand new TKX or auto from SST this is not cheaper than say a used A833. About the same as four speed used redone. But if you go Brewers which I would have its more...

Managed to get my mount system ordered I went all Hooker Blackheart may have to modify where it mounts but this gives me a good solid base and replaces the huge upper cross member hoop. Bhs572/574/578

I have a factory 3.91 rear end in my 2021 Ram. 2100 rpm at like 75 mph.

Took a bit but made own frame connectors need to weld in now. Then I can pull transmission and install the flywheel for the ZF. I have a hoop combo by from Hooker Blackheart. It replaces the loop support for torsion bar upper support. Hooker BlackHeart BHS578 Hooker Blackheart Transmission...