Search results for query: *

Awesome! Good looking out! I appreciate it!

I can use them!

They should be shorter and shouldered, perhaps 1.5 inches long, I am having a hard time finding a picture

I think so, the lap belts were still installed and I kept those bolts together. They are shouldered and two different lengths. I have some 7/16-20 1 /14 grade 8 long bolts that will fit but I’d rather have the original and shouldered to allow the top mount ( for shoulder belt) to swivel.

Unfortunately mine are missing and the shoulder straps as well. I updated to buckets and a 3 point seat belt but wanted to use the stock style hardware.

looking for two shoulder belt bolts. The ones that go into the roof section. I’m out in Northern CA. Thanks!

Has anyone installed a knee knocker along side their stock heater? Just wanted to get some ideas on. Punting location. I saw one posting with a knee knocker unit but it looks like the original heater box was removed. Anyone have a cool only unit that can share some pictures? My heater works...

I’ll definitely look into 1.03’s as well

I will grab the part numbers but I swapped from a slant 6 to a magnum 318. I bought some used 318 torsion v8 bars. I’ll look up the part number. Here’s an old pic of the ad If I recall correctly, they are .850 bars

I can always raise the height abojt 1 more inch to add more clearance to the bar. Should put me at 4 inches. From what I’ve seen, it appears the QA1 bars hang lower than others

torqued everything down and reset the cam bolts and tightened anything else that was overlooked. Looks like I’m heading in the right direction. Car is sitting fairly low. The sway bar is about 3.5 inches off the floor though. Car is not sitting on bumpstops and the A&B was set to 0...

Ah, I appreciate the info and reply! I got the manual handy and will read over the settings. I thought the QA1 system would be different but it’s pretty much a bolt on / OEM replacement. The car appears to be high since it’s on the jack stands. I torqued down the k member Bolt. I didn’t...

Reviving this thread! I also installed the Qa1 torsion bar system in my 1969 Dart and out of 2 shops. No one had been able to align it. I can’t get anywhere close to -.5 camber. Today I crawled under and reset the camber bolts to having the front ones to provide max caster and rear ones in...

I’m currently on the same boat. Was installing new dash vents and accidentally broke a pin. The slider that’s made out of plastic is also brittle. I can try to pull my assembly out and get you some dimensions.

thanks for all the help everyone! I was looking for the hole to hole on the mounting tabs, and possibly the width of the speaker itself, I’ve seen brackets that seem a bit offset. @Dana was able to answer the questions . I do appreciate the pictures, I was looking at the retro sound speaker...

Hi everyone, my Dart is in the shop so unfortunately I dont have access to it. Does anyone know the dimension or distance between the two mouting holes and possible the width of the speaker? I am looking at replacements or creating a mount on CAD and sending it to laser cut or water jet. I...

Price down to $2300 if anyone in the Bay Area is interested

Bump.... Title and registration arrives this week Stop looking for a slant 6 car if anyone is up for a trade

4500k obo Located in San Jose CA 1969 D200 1968 Style Hood 360ci New Airgap Style intake New Edelbrock manual Choke Carb Swapped in a 727 and changed the filter and gasket Still has original 727 to go with it in case you want to rebuild and swap back in New wheel cylinders New...

Hi Guys, I am looking for the same trim, but just the driver side front fender. My 69 is a custom and the front part of the trim ends in a point. Not sure if anyone has one aying around. Can be driver quality since my 69 is Ratty. I am also located near the OP but in San Jose

I have the SBP one I took out of my 69 Dart. Still have a set of 13 sbp wheels and hub caps. I need to check the ratio but it's in San Jose CA

Hi There, does anyone have a new or good used Bench seat cover? I want to freshen up the bench seat in my 69 Dart. I have headrests. Shipping would be to 95111 Located in San Jose CA

Thanks all got some!

I can send you the Passenger side mount if you can use it. Just pay shipping, might fit in a small flat rate box. I won't be needing that one. Probably expensive to ship : /

since the original kit I used was slant 6 to 340 , it came with the correct left side mount. The passenger side is this longer box looking one. That sounds like whatever I find should fit even better!

Hi there, looking for the passenger side engine bracket for a V8 K member to 318 magnum (technically 340-360 should fit) I don’t mind a 318 mount even if I have to make shims. Currently swapped from a slant 6 k-member to a QA1 and realized my drive one fits but not my passenger side. I’m...

Looking for a 4 speed Bellhousing cover. The front thin one. Should be 10.5 Small block versioin. Figured someone might have a spare laying around before resorting to new. Thanks! I am located in San Jose CA 95121

If I get to finish my 4 speed and Qa1 Swap into the 69, I will most likely go. I have missed all other times due to my cars being down and here I am again -_-

Hi there, looking for a bellhousing cover for my A833/ 318. I believe it’s the 10.5 one I need. Doesn’t have to be 100% pretty just need to cover the clutch and flywheel. Figured I’d check on used ones before buying it new. I’m located in San Jose CA Thanks!

Hi there, I sold my last slant 6 vehicle and have this intake left over. The numbers seem to show up as a super 6 intake. It is cast iron and pretty heavy. Will ship at buyers expense. $250 I have a 2bbl carb brand new from Amazon, $50 for it. Items located in San Jose CA 95111 will...