Search results for query: *

Looking for a good set of seat tracks. Found a set locally.

For a 1968 dodge dart. Tapered bolt. Nut too if you have it. Thanks, Al

I think I have some. I'll check when I get home

Looking for Black if possible but any complete undamaged part would be fine. Thanks, Al

Same thing as straightlinespeed. Bought 2 sets a few months ago but no covers. Would like 2 if available. Thanks, Al

I looking for 7 clips that attach the hard trim to the headliner. I borrowed the following picture from this site to help. please respond with price and shipping to either Blaine, Washington, 98230 or Surrey, BC. Thanks, Al

Will take photos when I get home this afternoon. Too dark last night and got a lot of flash making it hard to see. Al

I have one that I bought from another member a while back and didn't use. I took it out of the box and polish it and it is in good condition. All set for shipping in a box. Let me know if you still need one and I can email you the pictures. Al

OK, How much and shipping to 98230

For my 1968 Dart. 67-76 should be the same. Thanks, Al

I have a set of 69 340 inserts but am looking for the correct 68 ones. Let me know what you have, condition and price. Thanks, Al

Thanks for the advise guys. The picture that Tony presented is exactly what I am facing. Will probably wait until the weekend to tackle it. I am thinking that I could maybe get the correct size bolt and put it in from the pivot shaft hole after the stud is drilled out (it will be tricky) then...

So I just rebuilt all the wiper stuff in the car and go to install and find the driver side wiper pivot stud is broken. I bought the car disassembled so didn't know until now. There is less than 1/4 inch left in the cab. The stud is located in the plenum and looks like the 2 studs are connected...

Not yet.

Looking for 2 of the chrome knobs. Thanks, Al

I bought a New Cat iron water pump from Moparmat2000 which is coming and That is probably what I will have to install. I just measured the 3614378 crank that came with the engine and it is 3 1/8 inch tall x 7 1/4 inch diameter. It is a double grove pulley. I found a post from Chrisf from 13...

Well here's your answers. the timing marks are on the drivers side and lower rad hose outlet is on the passenger side. I think this pump is for the later pulley set up. Crank pulley is not installed in this photo. Engine is now installed in the car.

I already have a new switch and cylinder. Just need the nut. Thanks

Here is the whole story. I have a 68 dart that came with no motor. I got a 69 340 that only came with the crank pulley. The crank pulley on the motor is a 3614378. The machine shop that did my engine replaced my old cast style water pump with a shiny new aluminum pump. This appears to be a...

I need a 2951836 pulley 6 7/8" diameter. Thanks

No a/c and no power steering. Single groove, but double would be acceptable. Thanks, Al

Added photos of the bezel I am looking for and you can see the reason why in one of them.

Got one from 694spd. Thanks Jon!

I'll take them. I have a set of blue ones that I was gonna dye black but... this would be easier.

I got the car without a wiper motor and crank. Just have the arms and pivots. I purchased a 3 speed motor from a member on this site but it does not have a crank arm. So I can't send you any pictures. I can't see them being much different through the years, all 67-76 should fit. Thanks, Al

I think I have a bezel for it but either way would be OK. Thanks

Going in a 1968 dart if that makes a difference. Just lined up the motor but it does not have a crank. Thanks

Need one for a dart with lower dash pads. Thanks

Hi Tony, I'm looking for a wiper motor for my 1968 dart. I have a variable speed wiper switch and I think I need a 2822962, 2808801 or 3004114 motor from what I have found. Any chance you have one? Thanks, Al

Looking for 10 of these. Mine look like the ones used on barracuda and b bodies. Not the 69 dart finish panel style. Any help would be appreciated. Thanks, Al