Search results for query: *

  1. desy500

    show me your early A!

    1965
  2. desy500

    Dart 440 ?

    A friend saw this car in Delaware , and sent me this picture , sorry he didn't send a picture of the whole car. Anyone have any details of a 440 Dart ? I never knew they did it.
  3. desy500

    Adjusting the bearing preload

    update , so looks like the PO did one side and not the other somewhere along the line , both drums are different makes , one is 1 m.m. smaller where the brake shoes touch, one side has timken outer bearing made in the us , the other side has national made in mexico, although they do have the...
  4. desy500

    Adjusting the bearing preload

    Yes I read that on this site last year , and tried to do that way , I think i was following to turn it some moire till the wheel wants to stop spinning , and then back off and put in the pin. that works on one side , but can not tighten other side till wheel drags . more info to come...
  5. desy500

    Adjusting the bearing preload

    yes the front. I am going to pull both hubs again today , and check if the issue remains with the hub , or the spindle. I will let everyone know.
  6. desy500

    Adjusting the bearing preload

    Well , I am thinking that if I can tighten the nut down by hand , and then another turn with a wrench , then the wheel should not spin . But it does , so is the hub worn out or the bearings worn out or the did the po put the wrong bearings on that hub? I have switched from right side to left ...
  7. desy500

    Adjusting the bearing preload

    Hi Guys , So if I tighten the nut down , and I can still spin the hub , where should I start to trouble shoot this ? 65 with 9 inch drums
  8. desy500

    Electric Choke help

    Sorry to hear that Dan , hope you days get better
  9. desy500

    OFFY DUAL 1BBL Intake question

    Thanks , Yes they are 1920 , jets are 55 - yes headers mild cam 4 speed factory , and original rear , 225 is .40 over , all was done prior to me , but have receipts from machine shop. I have rebuilt the 1920 's and changed it over to electronic , fires right up , but still smells rich , always...
  10. desy500

    OFFY DUAL 1BBL Intake question

    I know this is an OLD thread , but would like to know what size jets worked the best , I am running rich , thinking of going down in size
  11. desy500

    NOS distributor seals ?

    I ordered the 100 ct pack , anyone who needs a couple just PM me .
  12. desy500

    Large O ring on dizzy? Rubber or other

    Thanks Dan , the bottom seal grove looks a lot thicker then the old points dizzy I took out, is that size you gave for the 65 dizzy or the one in my picture?
  13. desy500

    Large O ring on dizzy? Rubber or other

    Dan this is great info , can you tell me what the size is on the bottom seal of the 1972 - 1985?
  14. desy500

    NOS distributor seals ?

    pulled out the old dizzy from my 1965 225 slant , to put in NOS Chrysler electronic dizzy. For the record , I never did this before. So I have a few questions. Do I put The big washer / seal from the old one on the nos ? And should the NOS dizzy have a seal on the shaft? NOS old
  15. desy500

    225 popping out the exhaust, but...

    I know this is an old thread , but I have a dumb question.. I just switched out my coil ( 1965 225 / 6 ) with a 1.5 ohm flame thrower , do I need to use the capacitor that was wired to the old coil ? should I also swap that out ?
  16. desy500

    HEI upgrade, wont start (no spark?)

    Hi Dan , not to high jack the thread , What do you think of the fbo box?
  17. desy500

    [WANTED] 7/16 distributor wrench

    Looking for a distributor wrench for /6
  18. desy500

    Electronic ignition upgrade

    Yes just looking to change over for better all around , not more speed
  19. desy500

    do you still have the parts to do the hei upgrade on a 1965 slant?

    do you still have the parts to do the hei upgrade on a 1965 slant?
  20. desy500

    1960/`61 Valiant Disc Brake Conversion

    Do you know which kit will fit with 14 inch ss cragers small bolt?
  21. desy500

    How can you check the spindel's

    I am thinking about going front discs on my 65 valiant , front drums are worn out , probable out of round ,Don't think they can be cut anymore, looking at kits for sale , but don't know if the spindle's are worn also. Any advise would be great.
  22. desy500

    [WANTED] Looking for this carb part

    Thanks , I got one .
  23. desy500

    [WANTED] Looking for this carb part

    As always THANKS DAN
  24. desy500

    [WANTED] Looking for this carb part

    I think the one I showed in the pict. was filed down , and is now too short . looks like I need one at least 1/2 " to 5/8 of threads
  25. desy500

    [WANTED] Looking for this carb part

    Air cleaner bail, for '63-'67 9" diameter air cleaner with Holley 1920, Carter BBS, or Stromberg WA3 1bbl carburetor.
  26. desy500

    [WANTED] Looking for this carb part

    got one Thanks Anyone know where I can get this part - holley 1920 carb
Back
Top