Search results for query: *

Looking for the trim that goes around the lock on the glove box (shown below). Not picky on color but black is best...

Hey everyone, I am having a hard time getting my tune dialed in for lean cruise, and I wanted to see if anyone has a reality check on me. WOT performance is fantastic, this is specifically only a problem for highway cruising. The car is a 340 Duster, 4 speed, 3.91s. The 340 is a pretty vanilla...

I have some shift rods that I purchased years ago as A-body shift rods. Comes with adjusting swivels. Full story: I am not sure if these are OEM rods or aftermarket rods from long ago. When I bought them, I was told they were for an A-Body. I used them in my 1974 Duster with an A833 and a...

I have the original steering box out of my 1974 Duster. It's works fine, but it is a 47 year old steering box at this point, I wouldn't expect to cut a second off your autocross time with it.. Firm feel charges $250 for the core, hoping that someone who doesn't have a core can use this. $70...

Hey Guys, I am having a lot of trouble with a rebuilt ("rebuilt") transmission I bought. The trans shifts into gear just fine when idling in the driveway, and is marginal on upshifts (minor clash), but I can't for the life of me get this thing to downshift into gear while the car is moving. I...

These were in my 1974 Duster for about 1.5 years. Ordered summer 2018, removed early spring of this year, stored in a garage since. Handle great and the difference versus stock was phenomenal, but ultimately decided to go a different direction with the car. These springs have maybe 1000 miles on...

I have been wiring up my accessories and megasquirt the past week, and came across these distribution blocks on Digikey I thought I'd share with you guys. Screw terminal on one end for heavy gauge connection, then 4 male quick-connects to hook up too. Pretty readily available on ebay too - look...

Hey Guys, I am looking for old two-post stereos (with a cassette deck) to replace my Alpine 7156 I am currently trying to repair. Really looking for a true 80s aftermarket cassette deck, not the AM/FM that cam in the car originally. I have the alpine connector (3x3 square), so I have a strong...

Looking for some EFI components. I am primarily interested in MPFI. This is for a 400ish HP street driven 340. 1. Fuel pump / EFI sending unit 2. MPFI Intake (and fuel rails, if you have them). 3. Throttle body. I am going with Megasquirt 2, so I would be unable to use any throttle bodies that...

Hey everyone, I purchased a Megasquirt 2 yesterday, and I am trying to work out a "starter" fuel injection system with TBI. Ultimately I want to go the MPFI, but in order to get running and start learning faster, I am looking for an aftermarket throttle body that includes the injectors in the...

Hey Guys, I've been working on a project this weekend that I've been wanting to do for months, and I figured I'd share in case anyone else wanted this info. I was inspired by a post from 72BluNblu many moons ago, and this weekend I had a go at it myself. Here's the situation - I've never...

Looking for a set of 1970-1973 Duster Rear Bumper Brackets.

Driver quality rear bumper, pulled off yesterday from my 1974 Duster. Ding near bumper jack hole from being lifted. Other than that, status-quo scratches and marks from a 46 year old bumper. Includes the molding that extends from body to bumper. $100 located in Bedford NH.

Hey Everyone - Took this shifter completely apart about a year ago, replaced the shims, cleaned everything up, greased it, put back together and drove with it for about 6 months. I didn't like the push down feature with the angled shift lever I have, so I pulled it out and replaced with a...

Looking for a A Body 8 3/4 housing. Located in Southern NH and can drive a couple hundred miles to pick up.

Hey everyone - I am looking to sell the original set of wheels that came with my 2013 Challenger R/T. They are 5x114.3mm, which is the same as 5x4.5", so they should fit on any BBP Chrysler hub. THESE WHEELS HAVE SOME SERIOUS CURB RASH - They work great and I drove on them for about 6 months...

Hey everyone, I am looking for the A pillar trim for a 1974 Duster - preferably Black. I can't find reproduction ones anywhere... Additionally, I am looking for the trim that goes over the rear wheel wells for a fold down rear seat - see the picture below. The part I am looking for is where...

Hey guys - Any of you know of any places that let you store and work on your cars? Graduated and moved out to an apartment, so now I need to find a place to work on my cars. I am having a brutal time on craigslist trying to find anything to rent for less the 700/mo. -Jon

Hey guys, Getting down to the details of my 340 build, and will probably be ordering heads before end of the month (Eddy 60179 or 60779). I'm running KB243s that stick out of the deck about .038" (deck was shaved a bit). I'm leaning towards running a thin head gasket and the open chamber 60179...

Hey Everyone, Pulling the 225 and 904 out of my Duster to get ready for a 340 swap. Currently in the car running and driving. I figured I'd put it up for sale while its still it the car so you can see it run. About 95k on both, engine runs nice, trans shifts fine. I drove this car from Indiana...

Looking for a set of 7/16" eye bolt or 1/2" eye bolt spring hangers for a 1974 duster.

Hey guys, been beating my head against a wall trying to figure out a leaf spring hanger situation I have. Long story short - bought the hotchkis rear spring setup and it was much lower than expected. Read some threads here, figured I swap some OEM ones in. Hotchkis hanger eye bolt is 1/2", the...

1974 Duster - Need a pair of stock, 1/2" eye bolt, spring hangers - bought the hotchkis springs/hangers and they are too low for my taste. Thanks!

Picked up a standard bore '71 340 last weekend, and curious as to what you guys think is "absolutely necessary" on a build, and what is more along the lines of a "nice to have". I picked up "How to Hot Rod Small-Block Mopar Engines" but this book isn't exactly what I thought it would be - lots...

Anyone know of any competent machine shops in the southern NH / Northern MA area? Just picked up a 340 and looking to have it looked over by someone who knows SBM.

I've been looking around local CL for a while trying to find a solid 340 and I came across one last week. It looks like additional holes are drilled out in the main journals, but this would be my first 340 so I'm not entirely sure.. This look weird to you guys?

Complete 7 1/4" rear, with springs and shock plates still attached. Only thing thay doesnt come with it are shock plate studs and the axle to housing nuts. Free to a good home. Words can't express how uninterested I am in shipping this monstrosity.

Looking to buy everything to go from Slant 6/904 to LA/a833. Prefer to purchase a complete/nearly complete setup. *Corrections - don't think it makes a difference, but my Duster is a 74 not a 73...

Just graduated college, saved up some cash along the way, so I am looking for a Duster project somewhere in the 3-6k (ish) price range! Located in New Hampshire. Moderately rust free is strongly preferred. Really don't care what engine - open to rollers or unfinished projects. Prefer manual but...