Search results for query: *

Vintage Ansen's & Pro-Trac tires on all four corners :)

Hi, I am in the process of putting new seats into my 71, a bucket set front & rear from a 72. On the rear upright, I have noticed a tab / bracket that looks like it fits to the body floor - is that correct as they isn't a hole / fixing on my floor.... Am I right in saying that the 72...

Hi, its a 66 small block car - Thanks!

Long shot request, as title - WHY? Thanks:D

Long shot request, as title - WHY? Thanks:D

Thanks, the vertor is one that came with the motor, in fact I had bought the motor and trans as one and just dropped it in. Like you say, there must be another problem....

Hi y'all! I am in the process of getting our 66 valiant running after fitting a 273 (67 I think) and 904 trans. I have fitted the starter (can't remember if it came with the motor or not) and it does not appear to mesh with the ring gear? The ring gear does not seem to be worn. The socket...

OK, PM sent

As the title says, anyone??

Bill, I have an NPT adapter for the MC but there is a inverted flare on the ditribution block, so as you suggest, a 3/16 will not seal there. Good point and thanks for that! I will get the correct fittings and take it from there. Point taken on the dual circuit thing, will seek to upgrade...

Looks like I have worked it out - thanks guys. It lloks like the OEM line should be 1/4" and the fittings 7/16 unf". I have the fittings to make a 3/16 line. Do you think that would make a big difference?? Added brake pedal pressure perhaps?

Yes, you are right. There is a specific reason for getting the existing system going and will be a temporary fix. Once there, can convert it in the near future. At this stage, I just need to know for sure what size line I need (1/4") and fittings (7/16"??).....

Sorry, the Car is a 66 Valiant, single circuit manual. Bill, so I use a 1/4" line and the fittings are 7/16 unf?

Hi, I need to make a brake line from may new master cylinder to the splitter block. Could someone tell me what size / diamter this line should be (if not 3/16) and what size fittings I need? Manual single circuit brakes. The existing MC does not have a line so have nothing to compare with? TIA

Hi, I have a 66 Val. I am current running new brake lines throughout. There is an male to female inverse flare adapter on the end of the brake master cylinder that could do with replacing. Could anyone tell me what size it is? TIA

Hi, Would you ship this to the UK?

Still lookin ;-)

Thankgs for that

Thanks omahamoparguy! I was just wondering if the early cast exhaust mainfolds would fit a 318 until I get some headers sorted, that's all. Sorry to hijack the thread!

Thanks Joe! Damn, I was too late :-)

Was it just the intake that was different? Are the exhaust ports that same post 65 and same as the 318? Thanks

Are these still being made? - does anyone have any that they are willing to sell?

As the title says or information if repro is available TIA:wink:

Opps sorry, have been away. Thanks everyone for your replies!!

Would any know where I would get a rear gasket for the about. Is this the same as any other model? TIA

Opps sorry, have PM'd you

Thanks Gary, I had thought of this as I have someone in Nichols, Iowa taking parts for me ready for a container. I tried to track down a glass shop in Nichols on the net but just got a load of the usual search engine stuff which didn't really help....

As the title says, WHY? Other parts also required for 66 Valiant 2dr post TIA!

Cudamark, Thanks, I had seen this car on ebay and is going to supply the rear glass. Apparently, he packs in using building foam and a strong cardboard box to ship. He has no front glass. 64x2, Thanks, had seen this, but doesnt ship. Geoff, Thanks for the offer, I am definately interested...

Hi, Have you a front windshield for a 66 Valiant 2dr post going spare?