Search results for query: *

Pins 3 and 4 Anyone have some insight

Looked into them it’s an option, how ever I’m goin to be thorough and finish what I started. I am attaching a pin out I’m stuck on pin 3 and 4 ? Why is there so many things going to 1 pin

05 ram ecu 05 ram pedal I believe I’ll double check now swap specialties harness Hold the efffffin phone Holly makes a hemi harness?

Ok pins 3 n 4 on the brake pedal I could use a little guidance this is what I see pin 3 says fused ignition Ground Speed control switch output Pin 4 says I goes to c3 pin7 and c3 pin 14?

Where do you buy your harnesses? I’m open to options but this was a pricey harness so hopefully I can work it out as well as solve an issue that I have seen go unsolved, ls has all the support in the world I’m just trying to solve my pedal issue and share my results with the abody/hemi community...

Oe gas pedal from a part out, however I just got my brake sensor and pulled up a pin out and it has speed control signals. Etc the 05 ram brake pedal switch so my last hope is that it needed the brake sensor from ram, current set up is only a body side switch for stop lights I’m looking for...

I’ll live without mph on display for now but really I’m trying to end the pedal cut out issue

Do you have other tuning software where you can send me a data log and tune file or I can send my hp tuners to you and you simply scan and send if not it’s cool it’s asking a lot but I’m about to spend on a new harness Hotwire auto said they are very sorry and know the harness swap specialties...

I have only 3 fault codes Fans Air temp circuit high Bank 1 circuit high I have the codes written down if you think those can be it On hp tuners I just don’t read mph so I ordered a new brake switch I was using the doge dart one and may be missing inputs? How many pins do you use all of them...

05 pcm Thank you for checking @loganscuda another question what is the consensus on the brake switch-stock ram or stock dart? Other than that I cannot figure out why I’m only missing mph and pedal cut out, the car is damn near race ready maybe a new harness

Ok I’ll do what I can on my end till then I’m betting that’s it, if so the real question would be what does that wire see as bypass; voltage, ground, modified signal, etc. Good luck with the renovations sorry about the damage to the house

C3pin15 I have nothing @loganscuda this would be the pin I ask if you can check ^^^

What about c3 pin #5 speed control vacuum vent solenoid are you guys running that part? My speed system is solely 2 speed sensors on the trans where in theory I have 0 speed control inputs?

Issue only presents itself in gear, in park I get full pedal.

I’m not with the car I gotta scan it and update for the 4th pin on ecu too I’m really trying to make pulls with his car so I wanna be able to slam that pedal I know that my hp tuners doesnt catch my mph

C1 Pin 8 vehicle speed signal #2 Pin 13 vehicle speed signal #1 C2 Pin 15 tp sensor return Pin 21 tp #1 signal Pin 23 map signal Pin 28 tp #2 signal c3 Pin5 speed control vac vent sol Pin 7 speed control supply Pin 12 speed control vac sol Pin 14 brake switch #2 signal Pin 15 speed control...

Bump I’ve gotten further into tuning on another one of my cars are am going to explore some pedal tunes and look for some apps 2 info and finally solve this, if @loganscuda would help me with a pin confirmation I’ll dig out some pin out info

Yes they have many many issues the same, Andy has scammed many out of stock harnesses and ecu’s sorry to hear that, I worked my *** off so been driving as is but soon going back into the project stage so I can complete and compete the car in time attack tracks and local car shows. Seems like we...

Idk but my speed doesn’t work either so I think that’s my pedal cut out?

Swap specialties harness worst harness ever!!!! I wouldn’t even be surprised if I had more wiring issues but I think I checked all the trans and sensor wires for speed so idk? Blake from diy hemi says maybe I have a short? Maybe in the pedal? I am using a 05 hemi 5.7 545 rfe 05 computer but ecu...

It’s an abs thing I’m reading up on it else where and will link later one of the speed inputs comes from the abs wheel speed I think it was, it may require a modified signal? Haven’t completely got it but I know it only happens to me when I give it all the beans, I have a video of a beautiful...

Did your plan work? I’m having the same issue and need a solution. Wondering if the Ford 8.8 sensor will work.

New plasma table in house and now that i can neatly make the flanges i will be making a small run (5) of these deletes for the 5.7 truck hemi. if anyone maybe interested contact me. PST has a 16:1 "quick ratio" that i really can't say enough about.

Well folks i would hate to tear it all down after all this work but is there a relearn for timing i believe my car is pulling -64 degrees timing... When the car runs every seems fine! Still only ran once just taking the time to look over some data i logged during crank missed the log when it...

Prolly a stupid question why is there a ground on this part i just got it in the mail... Hopefully i got a solid runner after the install

Ok after banging my head against a wall, mind you i havent gotten the new regulator for corvette yet, and had to fix some wiring. i hit it with a tiny spurt of spray amd boom the damn thing started up and idles and accelerater respomded very well. However it will not start on its own and upon...

Ok here lies the issue no spark and injectors not firing.. Swap specialties stamd alone harness is not worth the price alot of it was right wiring with wrong connectors i looked past it.. Now the wiring is the culprit. This is only my expirience it looked and sounded good amd dont get me started...

External its a generic in line that is putting putting out 100psi and needs a regulator but my regulator bleeds pressure dowm fast and is all over the place. Is also pressureizzing the gas tank. I think its returning all the fuel to the tank. Im going to order that vette unit. Or similar unit...

Ended up using 3 in black pipe 3/8 mpt