Search results for query: *

Thanks @halifaxhops , I did not see it on the site. Sent them email to verify.

I changed out the wiring on my 71 demon 340 with M&H factory style harness from YR1. I recently got the factory 71 idle solenoid rebuilt/refurbished and want to install but I do not see a wiring harness for it or wire from the main harness? The FSM shows a dark blue wire going to the ballast if...

****ALL THREE ITEMS SOLD****

****ALL SOLD**** Slightly used - Power Master #3257 starter - used only to get the car running after engine rebuild then found date coded starter - NEW $248, will sell for $100 NEW - Tuff Stuff alternator 130 AMP - I had painted the pulley to match OEM, then found correct date coded alt. -...

Hood scoop nuts are sold**

Rallye dash lens - PC Classics with black insert

NEW - Header bolts hex head (9) - $10 NEW - 1970-71 340-440 Carter AVS Idle solenoid bracket - $30 NEW - A/B hood scoop mounting nuts x 11 - $15 ***SOLD*** USED - freshly refurbished A body blower motor mounting bracket to firewall with new gasket - $30 ****PM IF YOU NEED TO SEE CLOSE UP...

NEW - Pack of (3) different Master cylinder gaskets ; 2) foam 1) gasket material - $6 made by Detroit Muscle Tech. NEW - 69-74 brake distribution block part #BLK250 - $60 NEW - (rebuilt) by Brake/Equipment Warehouse in MN - Weatherhead brake distribution valve - $200 NEW - 72-76 A body Rear...

Mr. Norms - Dream Motors Super Charger vintage sticker - $40 - Will sell unframed for $25 Dodge Scat Pack banner - $25 ***SOLD*** NEW - A BODY Fresh air vent to cowl seal (DMT) 63-66 fresh air vent to cowl, 67-76 NON A/C heater box to cowl, 67-72 AC heater box to cowl $8 NEW - (1) Rallye...

NOS gasket is ***SOLD***

NOS - 340 McCord Mc4522 LH exhaust gasket. Left end flange separated from the rear (see pics) Easy repair and once installed should not move. $500 + the ride Very hard to find these days as the Mopar Performance repop was discontinued two years ago. PM here on the board- Located in NW Indiana

Looking for power disc brake master cylinder - Mopar part number 2944453 and will have casting number #2229171 on the bottom. Similar to attached photos - PM here on the board please -

@toolmanmike - Yes that was done a week ago. Both horns tested out as bad.

****SOLVED**** First; THANK YOU to everyone that took time to help diagnose this issue. Been away for a few days for baseball and wanted to report back. While working with these horns, accidently dropped one on the garage floor and when I picked it up, there was a chunk of crud on the floor...

@Swinger 340 - did that and still nada - removed the powedercoating with a Dremel tool(brush) see next post.

@Dana67Dart - yes used a small dremel brush wheel and cleaned off powder coat on both the brackets, and the rad support area where they mount. Still nada.

Mopar buddy about 20 mins away has a horn possibly two that are known to work. Gonna borrow and see what happens. I cleaned the brackets with a dremel (mounting area) as well as cleaned up the mounting area on the rad support and still nothing. Leaning heavily towards the horns are bad. We'll...

Already did that and nada, both while still attached to the mounting bracket and without.

Thank you, will check them with this method tmrw and report back.

@Dana67Dart and @Demonx2 - I see your points (great ones too), but still confused as to why I wouldn't get a honk when touching the wire from the battery to the horn terminal?

I have those through the rad support and into the horn bracket

@Demonx2 - well I am getting power at both plugs when the horn button is pressed - test light illuminated with each horn press. I'm just confused as I ran a wire from the battery to each horn terminal and nada.

Ok, hooked test light to each of the plugs and had my son press the horn button, each horn press resulted in the test light illuminating. So it appears power is getting to the plugs, so must be grounding or the horns are bad, but as I stated I ran a power wire to each horn and nada?

@340wedge - ok, will check at the plug and report back. When you say check the ground? Which ground? At the bracket on the rad support? The brackets were previosuly powder coated, so perhaps I should take some of the paint off the bracket where it meets the rad support? But will check the two...

71 Demon - ALL new wiring; under dash, column, engine etc and NOS horn relay. Horns had been working - Prestolite pair that I had the powder coater PAINT and not powder coat due to the heat. Horns stopped working, checked fuses - all good. Standard base steering wheel - push the button and...

@Oldmanmopar - thank you! I think I have the correct cap coming from 521 Restorations. then I'll scavenge the insert for my cap.

Looking for 1971 only drivers' side idle solenoid bracket for 340 Demon. I believe it's the one shown in the photo. PM here - thanks!

BRAND NEW Carter AVS solenoid bracket - retails for $70 - sell for $50.00 USED - 23" hood pin cable set: pins, 23" lanyards and new screws (no gaskets) - ****SOLD**** BRAND NEW - large MC cover - cad plated in color - ****SOLD**** Prices don't include the ride - located in NW Indiana PM here

Not sure what cap I need for the Demon 340? Current cap appears to be 72-up? I need to find the “insert” that I can change out so the cap can seat properly. Purchased a couple of caps from Vans, but neither fit. Also how about the filler neck does it look correct? Thank you!

***BOTH ITEMS SOLD****