Search results for query: *

Found it Push-In Pipe and Tubing Grommet for 1.05" Hole Diameter | McMaster-Carr part number 928031K Install last night with help of WD-40, it seated pretty tight.

I'm not it forum for a long time. While you're at it, it would be nice to add a tensioner. you wont regret.

opps, my bad sorry

just use 3/8 extension and you're done. stop wasting money

I found this http://www.campbellenterprises.com/318-stroker-kit-mopar-318-5.2-stroker-kits.php

I've found 1987 5th Avenue push rod from roller block with roller lifter using standard rocker measured at ~ 6.5". How about Cran 69628-16? It is measured at 6.58"

Hello Folks It is a 1985 Roller Block with stock lifter. 302 heads Comp Camshaft XR268HR-10 Hydraulic Roller 273 Adjustable Rocker I've seen this set up somewhere but could find it. I'm looking for cup push rod with appropriate length that would go with this set up. Please advice with...

Ok. Found roller lifters from 87 5th Avenue, with spider and lock down thing. Still trying to figure out what cam for my set up: I know I will need roller camshaft and shorter pushrod to accommodate taller lifters. This plan is just a daily driver for 1973 Plymouth Scamp with A/C, P/S...

Thanks for all ideas and feedback. Sorry for upside down pictures I Picked up the block today for (4.25 bills) It's a standard bore Block number 4323330318-2 Date code 84 Crank number 4751841 (cast or steel) - Could it be 340 Crank? Inspected -No rust in any of the lifter hole or anywhere...

Hello Folks I'll be buying this 318 short block. The seller said it's a 1985 He stated "This was a new factory warranty replacement but never installed by owner" - What should I inspect for? This plan is just a daily driver for 1973 Plymouth Scamp with A/C, P/S, 904 transmission, and 7.25...

Hello FABO I'm looking for bottom end rebuild kits for 1973 "318". Search around and found: Engine Rebuild Kit Dodge Chrysler Mopar 318 5 2L OHV V8 1970 1973 | eBay Need advice on EngineTech. Should I or Should I not? Why? Thanks,

Hello FABO I'm thinking putting this on LA 318 for 73 Scamp. Any advice do and don't? Thanks,

Make sure to seal, seal, seal, and seal to ensure no leak because you don't want to do it again.

I understand that. Will be replace when break or $$ available

These are the parts I gathered so far: 4323302 Head, open intake valve to 1.88” and exhaust to 1.60” with harden seat. 273 Roller Rocker with spring and push rod. M/T Valve cover. Edelbrock 2176 Intake manifold. Edelbrock 1406 4BBL carburetor. ProComp distributor with PC-91 ignition coil...

Knows there lots of option including cam comp, lunati, hughes. I also need part number that fit my setup.. Thanks

Hello FABO I'm getting a pair of "302" head with 1.88" intake, 1.60" exhaust valve. Both head will have .509" spring. Heads will be bolt together with 273 rolloer rocker. I need recommend camshaft for stock bottom 318. This will be street ride and weekend cruiser. Thanks

Check this out http://www.forabodiesonly.com/mopar/showthread.php?t=237129 Shipping to Canada will be more $$

Hello FABO Please advice bottom end rebuild kit for my 1973. Link would be helpful. This is what I gather so far. 318 stock bottom end (looking for upgrade). Something like 0.030" over 4323302 Head, open intake valve to 1.88” and exhaust to 1.60” with harden seat. 273 Roller...

Hello FABO I'm just about to mount oil pan onto an engine. Upon applying gasket and found there are gap in between (Red Arrows). Will this leak? it is a detroit Gasket. If it leak, any recommend gasket to have proper seal? Thanks,

Message is well delivered. That wouldn't be no fun and little to learn. Don't mention about crate engine. I know nothing about engine and I'm teaching my 12 years young boy how to rebuild engine with a manual.:newb:

Thank you I did lot of research, but most had bottom end rebuild as well.

This is just a street build, weekend cruiser. I also have stock "302". The though is to have 308 rebuild with 2.02" intake, 1.60" exhaust with mild bowl port for future bottom end upgrade or 360 block. I could rebuild "302" as well, then save "308" for future swap. Most head rebuild cost...

I read about this Cam K20-223-3 What would this cam do to my engine? Thanks,

Hello FABO I'm the the process of getting a "308" heads to the machine shop. These heads will seat on stock bottom 318, 904 transmission, and 7.25 rear. These are parts that I've been collecting so far: Procomp distributor Procomp E-Coil. Edelbrock 1406 Carburetor. Edelbrock 2176 Intake...

Duplicate, Please Remove Thanks,

Hell FABO I've read bunch of articles and threads about porting engine head, so I give it a shot. I recently acquire a set of "308" head from 1991 Ram Truck. I removed all valves and degreased the head. Visually, both heads look very decent so I didn't bother to take it to the shop to check for...

Hello Lokar would be last option for me while I can modity the bracket and extendend the throttle cable to another 2 inches. I just save myself ~$90.00 73Scamp

I feel your pain. On the day I pick up a 73Scamp, my family said "What?" "is it running? How many miles per gallon? Do you realize it is $4.67 per gallon? Why this piece of junk? and so on...... It doesn't matter as long as you can enjoy your ride..... 73scamp

Hello FABO I just bought a 4323302 head from Junk Yard. I was pull out from a 87 Dodge Ram150. It has stock 1.78" Intake and 1.50" Exhaust. I want to have machine shop to bore Intake to 1.88" and 1.60" for the Exhaust. Could I use "used 1.88" intake and 1.60" exhaust from a 360 head or I...