Search results for query: *

Got eddy carb problems on Mopar small block? Try viewing these helpful videos from eddy first. Once ya watch em, you'll be the expert now! LOL http://www.edelbrock.com/automotive_new/misc/tech_center/install/tech_vids.shtml John8)

Try these "How to" tech videos on Eddy tweaking! http://www.edelbrock.com/automotive_new/misc/tech_center/install/tech_vids.shtml BTW; That new eddy 1406 should run right out of the box. We had bought a new one for our 67 and it cleared up alot of problems. I do understand wanting to...

Now would be the time to put that new fuel filter on!:coffee2:

Again, as seen in my post above that I knew I would regret. Disclaimer; ONLY meant as a representation of what I was thinking at the moment (My thoughts per your request) and not meant as an expert should of comment, I am not a mechanic! I did not mean any disrespect or ill will of airing my...

Hey Rob, Welcome to FABO. I usually try to stay away from tech advise due to so many more here with more mechanical knowledge than me. But you asked for thoughts and as many here know, those don't cost me nothin so I share when asked.:coffee2: I have some experience with that carb on BOF...

WOW! The 1405 600 was pretty much plug and play with no adjust for our car but is mainly stock, mild cam, stock size exhaust but true duals with cherry bombs on it. Something else you might want to check in the vid, they recommend using a special spacer plate under the carb that has 4...

Their Carbs come with a dvd that has everything you need to know. You are an Edlebrock expert after viewing a couple of times. The same vids on the dvd are on their website under tech vids. They are there. I'd be suprised if you didn't get dvd in tuneing kit. Get ahold of them and tell them your...

1969 Dart slanty single bbl Holley 1920. Past year or two I have noticed some stange things in the carb world. 2 years ago was trying to get a 2 bbl carb for my 64 273. No cores avail at manufacturer. I was not willing to send mine away without a spare core in hand. Found one, bolted it up...

My 64 started doing this over the week end. Yesterday I "Cleaned up" the cap contacts, rotor button, points. Then would not start at all! Replaced points, condensor, rotor button, cap. Fired but ran rough. Adjusted points to .016 when on open lobe. Fired and adjusted timing with vacume guage...

I've got one on the 64 right now. 2bbl. Couldn't find a good core fore about a year. Found one on Ebay, put it on ran better, sent original to Chicago via local parts store. 10 days, $160.00. Git it back put it on, never adjusted, runs like new! Core back on my shelf for later use! Son bought a...

Go to EB's web site tech video section and watch tunning section. You will be an expert in 2 viewings!!

Also take a look at EB's web site under "tech video's". Very informative and usually included with the performer series on DVD, I assume your thunder series would be on there too. Good Luck!

Used a second donor bracket, 3 cuts, 1 trim, 1 drill, 1 grind, viola!!! Had pics on another thread. What do you think? Less than $10.00!:cheers: Almost for got they have new punch out bracke on ebay $40.00 see thread about "Help,new carb"? in this section.

Got it running finally. On test run the carb under load has a major vacume jet engine sound at mid range, med load, going to heavy load add high pitched whistle to the jet noise! Still no kick down. I guess I would have to adjust rod to tranny down and kick down sliding rod back a litle? What...

Just recently on a drive in the wifes 67 dart 318, (I can't belive I wasn't working on it) We experienced a sudden run on comming up to a turn made the corner RPM's up high pulled over. A small black vacum cap had fell off of a tree. Funny thing was I went looking around the parking lot for a...

Ok, Ebay wanted Approx $40.00 for bracket soooo...... Here is what I made from 2nd bracket like mine, 2 cuts, 1 trim, 1 grind, drilled. Not binding, less than $10.00. What do you think for temp untill I get a new job??:sign7:

Just got back from tour of junk yards today. I have quite a few slider bars and I'm pretty sure I can piece one together. I'm off to Ebay for the bracket. I looked at alot of mopars from 60's, 70's today with 4bbl and my "guide" was telling me he had 1 at his house but was saving it. His only...

I'm working on my wifes 67 dart with 70 318 in it. Everything on this car was hacked or butchered. The sliding rod I have has been cut & welded in two places. They should have cut another inch out of it! Hacks. Anyway I would need one to fit a 70's set up. I think the one in the green car looks...

I'm working on my wifes 67 dart with 70 318 in it. Everything on this car was hacked or butchered. The sliding rod I have has been cut & welded in two places. They should have cut another inch out of it! Hacks. Anyway I would need one to fit a 70's set up. I think the one in the green car looks...

What year/style van or truck???

JohnnyDart, how did you get away without running the adapter plate for the spread bore / square bore? Adapter plate Edelbrock #2696.

Camd64, do you happen to have any pictures of your linkage? Right now the way everything is set up, it looks like I need a shorter slide bar or different bracket?

I am still not being able to clamp throttle cable on the metal collar. Still @ 1" from collar. I think it's because of adapter plate I had to use. It added some on height. Also looks like I will be needing rear kick down bracket like JohnnyDart's, and my slider bar is too long. Someone had cut...

Way cool you guys!!!!!!!!!!!!!!! Do I use ported/timed vacume advance or manifold vac advance opening? The previous quadrajet rig set up, I checked when running and it had constant vac, but it was the wrong carb. What vac hole should I block off and what one to use for advance? Johnny Dart...

I hear crickets......chirp..................chirp.....................................

I need a new carb. Several things are happening that involves a safety issue. 1967 Dodge Dart Auto, has a 1970 318 with a GM Quadrajet Carb rigged on it. (before I bought it) I guess the linkage was not exact and they had to move cable up 1-2" in the clamp and they clamped it on the black sleve...