Search results for query: *

Inbox cleaned out

Have 3 sets of Mopar Performance P4452055 239ci, 3.9 liter V6 head gaskets. Cleaning house. 3 sets (pr) for $15 + shipping will accept paypal. PM. from 56007

Set of 15 old school adjustable pushrods for LA engines. One damaged. Not sure what brand, have had them on a shelf for many years. $25 + shipping. PM, will accept paypal. from 56007

*Meizere water pump block off plate for small block Mopar. Used for 1 dyno session. Black. Part #WP115S. $50 *New electronic distributor for B.B. Mopar RB 413-440. Factory style with vacuum advance. $125 *New Manley 221424-16 Nextex 1.640" roller valve springs. 250#@2.00", 800#@1.150"...

Old Mopar Performance book (2007) shows the non-CNC ported Stage VI head takes standard rocker gear.

Rockers are SOLD******* NEW set of Crane gold aluminum rocker kit; 1.6 ratio for Big Block Mopar with standard head, Edelbrock head, and others with factory offsets. Crane part #64791-1 complete kit with rockers(16), shafts(2), springs and shims. 1.6 ratio will give approximately .030" more...

Rebuilt Holley 750 cfm 4bbl, 0-3310-4 vacuum secondary, with manual choke. Has new non-stick gaskets, teflon fuel bowl washers, and power valve protection. Has stock jetting, power valve and squirter. Sell for $185 + shipping. New ones $370. ...........750 is SOLD............... Used...

In a 318 block, Crank will make 307 ci motor with 3.910" bore or 312 ci with 3.940" bore. In a 340 block, it will make 331 ci at 4.060" bore or 333 ci with a 4.070" bore. Many other possibilities especially with a short deck big bore R3 block.

New Mopar Performance orange ignition box, wire harness and ballast resistor with instructions. New car has MSD system so only used new distributor out of a complete kit. Have this stuff left over. $50 + the ride.

BRAND NEW, never used SB Mopar Kellog crankshaft destroked by Chrome-a-shaft in the late '70s or early 80's for Bob Glidden Race Cars. May have been for his assault on the Pro-Stock wars for his W-2 engines in '79 & '80. This is a 3.200" stroke forged crank for 340 main size with 2.00" small...

Mopar Performance SB intake SOLD. MSD 7550 Hand held controller....Reduced to $175 Fluidampnr SB Mopar..........Reduced to $200

MSD 7561, Mopar Perf head gaskets, Moroso u-joint girdles, & Mopar Chassis Book are all SOLD!! Thanks FABO!

FOR SALE: *Mopar Performance Small block dual-plane intake manifold 318-340-360, Holley flange. Used very little. $150 + shipping. *NEW MSD 7561 Programmable Launch Rev Limiter-RPM Controller. Never been installed. Must be used with MSD box that has plug-in chips 6AL, 7AL-2 or 3. Comes...

Still available

NOS cone type sure-grip unit for 8-3/4" rear. Had some light surface rust, but decided to disassemble , clean it up, relube and reassemble. In the process the box and part number were inadvertantly thrown out. Believe part number is #2881343. Helping out on an estate, has been on a shelf since...

Here's an updated list of what is left as of 10/14/13. Sorry, Not a fire sale on the stuff that is left. If it doesn't sell...will use it up someday. Thanks. FOR SALE: NEW Speed-Pro R9278+.035". File fit, plasma moly ring set. 4.350" bore. 1/16 x 1/16 x 3/16 with low tension oil rings...

PMs sent

Sorry, No 426w stuff here. PM sent

Low gear set is still available PM sent

Thanks, I'll check the wtbs.

FOR SALE: NEW in the box, Mopar P4876804 rearend yoke for the big 7290 U-joint and 10 spline 8-3/4" pinion. Mopar sells this for $180...will take $100 for it. Also will throw in a pair of Moroso aluminum u-joint girdles. PayPal and UPS available from 56007 Sorry, will not throw in the...

Used set of Program billet splayed main caps with ARP studs and bolts for SB Mopar to fit stock production 360 block. $200 + shipping

For Sale: TCS 727 torque-flite Lightened steel sun shell with gear and thrust washer. Little use. New is $165 for bare shell. Sell for $100 +UPS. TCS 727 torque-flite Aluminum drum. Also little use. Outside in nice shape and has been polished. Inside has very little clutch plate tang wear. No...

Bump

Tail housing is for a B-body.

Thanks for all the responses. Yes this ad is old but still have some things left. Pair Cragar Super Tricks - rears - 15" x 13", 6-1/2" back space, 4-1/2"-4-3/4" bolt circle. Drilled for screws. $250 NEW Speed-Pro R9278+.035". File fit, plasma moly ring set. 4.350" bore. 1/16 x 1/16 x...

SP2P is Sold.

May consider trades for 340 parts or Gen III stuff.

Freshly Rebuilt 440 Big Block Mopar cylinder heads. 1972 castings #3462'346', with factory induction hardened exhaust seats. Very similar to 906, 452, and 213 casting heads. Previously milled a bunch for compression. Now at 78 - 79cc, about 10+ ccs off. May require shorter pushrods! 2.08 &...

More pics