Search results for query: *

That a999 trans is basically a 904 with a lower (2.76:1 vs 2.45:1) 1st gear raito also known as the 'wide' raito 904. It also has a mechanical lock up torque converter. That lock up will eliminate any slip in the torque converter when it comes on. The even cheaper route is you can swap the...

You are correct in thinking the 2bbl pistons combined with that 270s & 3.23's are really hurting the low end/throttle response! I bet it starts to move around 3000-3200rpm but soft below that? The (lack of )higher compression is most definitely whats hurting you, combined with stock 1800-2000...

Hello fellas im checking here 1st to see if anyone has a slant six 4bbl intake manifold they would sell. Im looking for the shorter runner style. (Not long hyper pack style) offy, Clifford. It will be for a neer future turbocharged slant six. Thanks guys!

Ok thank you sir!

Im not 100% is a 20 tooth. From all pics of the green one it looks like its a 16t. But 20t should be what I need.

I think green is 20. I have 2 purple 18 teeth gears. Yeah no joke early 904 has 7 teeth on output shaft & a833/727 have 8 teeth! Kinda irritated me cuz was hoping it would be just how it was being I kept with the early trans flange.

Hey fellow mopar people just finished my 4-speed swap in my 65 dart GT. Speedo was perfect before swap, now it reads 8 mph fast! A little resurch found out early 904 has 7 teeth on output shaft. 833/727 have 8 teeth!!!!! (RRRRRRRR!) SO! Inow need a 19 or better yet a 20 tooth early speedo...

Seiing whats out there im looking for a early a body 4-speed hump for my 65 dart. Gonna make the swap in the neer future! Thanks guys!

I have a set of 65 commando covers id sell,ther still pretty dirty but otherwise good.

So your looken for a 65 273 4bbl manifold then correct?

I have the one off of my factory hi-po intake I would part with. I have electric choke now I wont be using the choke coil/stove anymore.

Pm sent.

Daves69 p.m. sent.

Hey guy's im looken for a STRIGHT pass side a body axle. stock axle small bolt pattern. mine the flange is bent! thanks.

Dartwizer here is some pics of the O.E. covers on my 65 GT. There still gross because I have a few sets of hi-po valve covers & the set thats on my car now were all ready re done hanging out in the basement just waiting. I can clean them up some if you would like. Still need to cleane up the...

That's an LD4B intake for 66-up 273 318. Hes looken for the D4B 64-65 only 273.

They pop up once in a while,but not to often.

I also have a set of 65 hi-po valve cover's if interested $100 & there yours.

Pm replyed pitbill.

Manual or electric? I have all parts for manual.

Nothen?

Cool moparbob71.2! Keep me posted!

Any one have an edelbrock 500 cfm AVS carb they would like to sell? dont care if man or ele choke. Thanks.

I know the pins is where the "factory" ballenced them but,im kinda anl... & i used some 318 thin wrist pins that lightened them up 60grm each! Plus who ever assembled it before i got the motor used thin pin with the flat topps requireing a ballance job to begin with. & fyi guy's egge is droppen...

I have a complete set of std. bore high compresion 273 charger pistons with the rods still on them! i scored another .030 over block that had never been ran so in the long run for me it was cheaper for me to s*%# can the low comp flat tops & drop a set of .030 over hi comp domes & reballance &...

yep, not the same but thanks.

Just as the title says looking for a Edelbrock D4B intake manafold that hasnt been "re"drilled to work on later 66-up 273 heads. Thanks guy's.

hello guys, not sure if im posting in the right spot (bear with me) just wondering if any of you had a FM converter youed wanna sell or knew of one for my 65 dart. Thanks!