Search results for query: *

Looking for a flat .063 snap ring for the Forward Clutch, about 5.4" relaxed, 5.3" installed. According to trans parts online, part # is 12878A, but transend says that # is for wavy. Neither place has it though and PATC doesn't even list it. Other suggestions for sources? I am working on a42RH...

That single one is the drivers side, I'm fairly certain both the others are passenger side.

Once Charlie is taken care of, I'm in need of the same thing, also really only need the door. Looks the same as his- mine is 68 Dart

I have one on the way from barracudakid, Thanks for the replies, & the info.

Sorry, thanks. 68 Dart, 2 door. Edited Title Edit; Interestingly, Year One lists their latch as 1968, with no other years listed. Another edit; Thanks to @Cal Tonsley "No I think that they are actually different, the 68 latch is different in that the knob locking mechanism of a 69 won’t hook...

I need drivers side door latch mechanism, as long as the guides aren't all beat up from a misaligned jamb striker pin. I already got one like that. Compare top to bottom “lip” in photo Price, & shipping to Chesapeake, Va. 23323, Thanks @cudascott You had replied to a thread in 2019 that you...

I need a pair of 67-76 leaf spring hangers. I have a pair of the Hotchkis 1” lowering hangers I could trade if wanted. Combined with the Hotchkiss springs it sits a little too low for my liking. Shipping would be to 23323

Willing to sell just the plates? I have all 2.5" hardware & drums are in great shape. 72blu is checking to see if he has a pair of plates

Looking for 11X2.5 Rear Drum Backing Plates. Here’s how to measure Thanks to 72bluNblu Set the backing plate flat on a bench. You'll need to hang the bottom 1/3 of the backing plate off the edge of the bench so that the mounts for the e-brake cables don't keep the backing plate from sitting...

1/2” bolt size, Thanks, didn’t realize that

Looking for a Pair of Leaf Spring Hanger Brackets.

I have 11 x 2-1/2 drums. Somebody in the past put a spacer under the drum. If I remove the spacer, the drum scrapes against the outer lip of the backing plate. I believe, by reading other posts, that there are different backing plates and I must have the wrong ones. 2” maybe? I would just...

Thank You for the info. I did end up ordering the full set. I just needed the springs, but at 4 each plus tax, but then they wanted 11 for shipping. It was close to 20 dollars to get 2 springs. The full set cost a couple dollars more & shipping was the same

Got new fenders because originals were loaded w bondo & scewholes from old wreck& a lot of rust. Forgot to get little stuff like headlight springs. Not sure what oter years besides 67-76 fit, but I need a pair that looks like these. (No, I don’t expect them this shiny)

The new ones I've gotten have been crap, perhaps I don't know the right source.

Need 2 light bulb sockets for 1968 side marker lights And 2 tail/brake light sockets (I think almost any year works for these) for 1034 or 1157 bulb if anyone has a trunk harness that aint worth a crap, I’d buy the sockets

Sounds like you want to get it back to the customer quickly, no? Sounds like "30 bucks at AdvanceAutoParts" is the way to go, you're going to spend that to get someone to overnight you a spring

I believe I saw that somebody purchased the rights, or tooling or something to Schumachers business. I can’t remember offhand though what company it was. I’ve been scrolling through everybody that I get emails from, but haven’t found it yet. They should be out there though.

I sent a PM to @davescuda about NOS ones, but in the meantime, anybody else?

I have a 68 Dart, but I believe they are all the same 67-76, no?

Hi Y’all I’m looking for the 2 trim parts at the front of a vinyl top car. Example in photo. Please no pitted, rotting ones, Thanks

I think mine bolted under the bumper bracket bolt rather than to the frame directly, then again I could be wrong, so this reply was pretty much a waste of time. Its been so long since I took it apart, I'm starting to forget things, though I feel when I get to things like that, it will be pretty...

Yes please on pics.

Thanks OldManMopar, I only need the 2 at the top of the A-pillar, I have the rest in great shape. That is a nice set for somebody, as AMD charges 209 for the same set of parts.

Can either of you provide photos?

Let me know if you got em, thanks

I need 2 good vinyl top trim pieces that go on the a-pillar. Thanks FABO

Its not so much only being able to use the White background, its that you need to use the one from that year. Florida used to issue new plates each year but which spanned 2 years, and changed color for quick identification of out of date registrations. I have a 69 plate which is White on...

Would mounting the bar to the K then centering it up, hanging the mounts with the bolts, then welding them where they rest on the arm be viable as opposed to eyeballing them off a photo? I ask because I am going to be mounting a anti-sway bar And that’s how I thought I would do it.