Search results for query: *

63-5 are the same,66-7 is the same,68-9 is the same 70-1 the same

There was a steel support plate that went in front of the controls if I remember right

They go on the bottom or back?

Where do they go on the seat?

I think Dart and Cuda used the same rear side panels and rear seat on the 67-9 cars if I remember right

Did you end up needing the horseshoe foam? I am about to place an order and I want to make sure I have all I need. Thanks

I'm not sure if Dart sedans are 111" wheelbase and I'd make sure both the car and the carpet are for the same wheelbase. All of the other A bodies are 108" wheelbase.

I used 66 tracks and seats in my 67 and they worked fine. The 66 actually have tilt and some other adjustments built into the sliders. The 67-up do not

They claim it is Legendary foam in the description

Tamraz is near me and running a 50% off sale but they are out of stock and Classic is only running their sale until midnite tomorrow.

I need the seat foam for my 67 Valiant and I have never noticed any seat foam U's separate from the seat foam on original seat foam in any A or B body I parted out. Are the U shaped foam pieces needed to complete a set of seats? I have never heard of these and they don't have pictures. Has...

You can

It's a 1 year only color and the parts used are hard to find. This is a Valiant with the same color....I think.

I think 70 and 71's are the same and use a seperate hard back cover. I don't think 72-up have a seperate back cover.

looks like the wrong horn button

The 73-up backs get screwed to the wheel well down low. The 70-2 have a tab that goes through an eyelette and folds over.

The fronts will work but aren't the correct pattern. The rears are Valiant only. I have a set of black Signet panels for a 2 door. I assume you need them for a 2 door. I also have 2 sets of 4 door panels, 1 in black and 1 in red.

They didn't make a 72 Dart sport. The difference is in how many speeds it came with and if it had power washers. Got pics of the backs of the switches you bought and of your wiper motor?

as long as you use one from a duster style body. The rear sail panels require a special tab or hole to secure them.

I want to say 13/16 on the heads.

The 69's also had a simlar wedge shaped headrest without a chrome band.

I don't have a pic but it does run down the driver side and lays on the floor and passes around the inner wheel tub and the should be some hold down tabs for it once you get past the wheel tub and then goes along the back panel and passes through the trunk latch bracket to run to the PS.

The front will work but I'm not sure on the rear

Bench or buckets? The 66-7 buckets are the same (hard back) if you going factory but 68-73 (high backs) will also work but not correct. If bench, the 67-71 or 72 are pretty much the same.

Yes. The 67-76 Darts share a lot of the same basic parts like front and rear glass 67-76,rear seat frames 67-72 I think,glass trim 67-76,door panels 67-72. Is he local to you? If not I'm sure AZmopar has one and he is near you.

The bench yes,the rear no but you might be able to fit the cover to your frame.

Just pull it off. Pic of the wheel?

Remove the column cover,drop the column some,the dash heater switch assy (two 7/16 nuts and an allen wrench for the slider bezels),radio,speedo cable, then reach up above the cluster in the back and pull the harness down out of the securing loops.

Just some 1/4 inch long wood screws if it's the cardboard one with the tin nuts already in the cardboard.

^ what they said. There is also an adjuster bolt that goes into it and a nut that secures it to the bottom of the door covered by a body plug.