Search results for query: *

FOUND 2/12/24

wanted 1970-74 198 slant six connecting rods with part number 2951260 Looking for a set of six.

Classic industries has 11" also. I'll let you look up the part numbers.

Classic industries has them BRAKE STRUT 10"B-body MN431003 $27 PAIR BRAKE ACTUATOR LEVER 10" B-BODY MN431006 $47 PAIR

I narrow and straiten 8 3/4. This one I'm putting together right now. For me its easier to body work/ grind the rust out then DA the finish, because its thicker metal.

I believe that I have a pair of SBP 8 3/4 backing plates, I'll have to look for them. E-mail me a t convx4 at yahoo.com I don't always log on when I visit FABO

If a different five button switch is used the cars wiring will need to be updated to work with the switch. If I was spending your money I would buy a new five button switch and update the wiring.

I parted out a Dakota, think it was a 96. It was an auto. Should have the brake peddle. Let me get it out and take some pictures. Was there any other associated parts you were looking for?

What car?

How may grooves?

I have a good used a-body 10" brake drum if interested.

I think that I have a original style 73. Tomorrow I can get pictures and dimensions.

Looking for 8 1970 type 14" big bolt pattern Steel wheels, these should have the four nubs to hold the dog dish on. Along with a round center hole and flat ring the lug holes are in. Lug holes need to be good. Not worried about the outer rim. Prefer pick up in the St Louis Mo area. Might...

If looking for one wheel I have the parts on hand to make one. If you want two I'll have to get some more wheels to make the second. I'm in St Louis Mo. PM me if intrested

Looking for 60's RV2 Ac compressor with small block brackets. Preferably near St Louis MO. If in St Louis Mo and you just have the compressor I would be interested in just that.

Looking for an Early A body condenser. About 22 x 16 with the brackets tabs that measure 24 3/8 x 5 3/4 Should have lines that attach one on each side. I am working on rebuilding the under dash box and this need to complete my system. Thanks

Looking for one of each. A v8 and \6.

Looking for a metal two piece fan shroud. Also looking for a large diameter ac hard line that hooks to the fire wall. The rubber and other end don't mater.

Parts Wanted: horizontal line dryer ( The one mounted above the passenger wheel in the engine bay) and hard lines connecting to it. Metal fan shroud and mounting brackets for a six cylinder These will be installed on a 1966 valiant Pm me with pictures and price that includes shipping to 63026

I have my original dart 1970 340 4 speed drive shaft. It has been sand blasted and epoxy primed. If you are willing to speed $500. I'm willing to sell. PM me

When I did my 70 dart 15 years ago. The buns offered were not correct. The foam had to be cut for the seam to fit and another layer of foam added under the seat cover to fill it out. I was not happy that new foam was sold for a 70 dart but was really for a duster. This foam and covers was from...

I have a good used lens. Pm me. Make me am offer with shipping.

I have dart and scamp lenses They all have cracks on the lower sections but good. PM me and I'll take some pictures.

Parts are for my 1966 valiant, dart parts should be the same. The 1967 and older are different. Looking for the horizonal AC dryer and hard lines that sits on the passenger fender well. Also looking for the metal fan shroud for a slant six. The dealer installed under dash units use the...

I have an 85 GLH omni, that needs work if interested located St Louis, Mo.

Any rear seat from the same time would work, to repair yours.

Parts found Thanks

These are my under dash parts that I am working with. I am missing the bracket that holds the temperature slide lever also missing the cable and the fan switch on that bracket. First picture with dash bezel. The temperature controller (Silver) that has a probe that is fed in to the core is...

My measurement of 11.5" was with the rod compressed. Mine is exposed to have two ports on it one on each side of the diapharam. I think with the rod pulled out it measured 12.5". The important thing is that the two mounting studs are on the same same side as the rod.

One of the nubs that the vacuum hose attaches is broken off on mine. Is there a write up on how to open it up and make the repair? Where do you get replacement parts? Please enlighten me, I'm up for the challenge.