Search results for query: *

I have been driving the dart for a couple days, so far so good.Clutch feels very smooth(100% kevlar disc) with comfotable pedal pressure via the hyd t/o brng setup.No burnouts yet,gonna break it in a little more.Transmission shifts perfect.I think the 323's are a little high ,probably a 373 will...

Ok figured out the vibration problem.Apparently my 360 is not internally balanced as I had thought.The reason I thought it was,is because there is mallory metal welded to my crank ,but all along I had been running a counterbalanced B&M flex plate.Called the guy I had sold the auto stuff to and...

Finally started the dart the other day.Got the hyd clutch blead out and adjusted ,but:( Ive got a real bad vibration while revving the engine in neutral.To me it feels like there is an imbalance in the flywheel /clutch assy.The higher I rev the worse the vibration.My engine is internally...

Right now I am using a stock shifter w/a hurst aluminum stick.I believe I have the 8" shifter.Heres a couple links you can choose from. http://store.summitracing.com/partdetail.asp?autofilter=1&part=HUU%2D5380178&N=700+4294821987+115&autoview=sku...

Sorry,no progress.As far as the t/o brng and fork situation I cant give you much there either.I think I did ask the owner of quicktime about that when I first started looking into the swap.IIRC I didnt get much of a concrete answer from him.I believe he said ford t/o brng and late 60's big block...

You are correct ,you will need a 10.5" ford 10 spline disk.As far as the p/p is concerned it depends on what type of throwout brng/linkage setup you decide to use.I had to use a GM p/p for a hyd brng application because the hyd brng dictated it ,but if you go with the std mechanical brng you can...

Ok, this is what I did and it should work for you too.Get Item# newitem29870999 (pictured in mancini link)from mancini or your local mopar dealer,then you need to purchase a roller brng for say a 1989 mustang gt 5.0L from local ford dealer or napa,atozone etc.You will then need to press the brng...

I probably wont be using the speedo adapter seen in the pics because of the girth of the hex nut on the factory cable. I will probably measure for another cable to be routed through the interior under the carpet and have speedometer solutions make me a fresh cable with the much more compact ford...

some pics of were I'm at

I think their kits are one of the better engineered kits.There just doesnt seem to be any way around cutting up the a bodies to retrofit these trannys and maintain correct driveline angle.There kit gets the tranny up high enough to mantain correct driveline angle.Just my two cents. justin

this is the bell I have; RM-6071 MOPAR 318/360 Bellhousing/Ford TKO 500-600/T5 Mustang/TR3550 - NEW! Height = 7.300" Trans. Bore Ø = Universal 4.850/4.910/4.685 Engine = Mopar 318/360 Trans. = Universal Ford TKO 500-600/T5 Mustang/TR3550 Clutch Ø = 10.5" Flywheel = 130 tooth...

barely used on ebay The "Z" Spec T-5 In 1993 Ford started offering a new service unit to the motorsport crowd. The "Z" spec T-5 (Ford part number 7003Z, also sometimes referred to as "World Class T-5". Most folks, associate the term "World Class" as meaning the best, however world class...

The bell is a Quick Time conversion bell,sb mopar to tremec/t-5. The box is a ford motorsport t-5 that would fit a mustang 5.0 justin

Some pics of shifter locaton and hyd clutch master on t-5 swap. I took a rough measurement from the seam sealer at the foward part of the tunnel back to the center of shifter handle;roughly 18.5".The stick I'm using is 8" with a 4"sweep puting the shifter ball approx 22.5-23.0"...

You got it justin

Thanx,Ive been out of the loop for a while.I did purchase a ford motorsport z-spec t-5,a quicktime sb mopar to tremec/t-5 bell,tilton 600 t/o brng,tilton 75 ser master,mcleod lightened steel flywheel,10.5 gm pplate , ford kevlar disc and a ford pilot brng.Project is not done yet ,but hope to...

Im seriously considering performing a t5 swap into my 360 dart for street and occasional road race track day use.Can anyone direct me to a post containing info on this subject or someone who has performed/documented this swap. thanx,justin