Search results for query: *

Here's some before correction pics. I.dont have any afters.

I used 5/16 smith bros. This is what I sent michael @ B3. Engine type, SB 414 Cylinder head type, Trickflow 190 The measured distance between the top of the rocker shaft and the valve tip of one intake and one exhaust. (FIG. A) This seems to vary 4 different valves, .277 I, .266 E, .281 E...

I bilt my stroker last year, it's eerily similar to yours. Short block: 360 based 414 4.06 bore 4.0 Molner forged crank 6.123 Molner rods Mahle inverted dome pistons 16cc's .276 top ring down ~ -.002-004 in the hole 10.87-10.89 compression .040 custom Cometics Quench .043 not sure on an...

Get ready to break out the hammer and grinder. Getting the milodon parts to fit is a giant p i t a.

5/16 smith Bros

Your saying 20/24 cold. Then take the hot and adjust so the hot is 20/24? Sorry it's late and I'm 3 drinks in.

The .557 also calls for 28/32. But I took out .004 for aluminum heads and cold lash.

Ant chance to look at the ones you got tonight?

There's just a tiny bit of play. But when the lifter it's filled it pushes up a bit.

Part# 91718 Mechanical Flat Tappet Direct Lube Extreme Duty Lifters; AMC / Chrysler V8 Howards Cams 91718 | Howards Cams

Quick question. I have a purple .557 Mopar shaft running Howard's edm solid lifters. I need to set lash. However the lifters have a bit of up and down movement between the snap ring retainer and pushrod seat. Lash will be .024 and .028. but I don't know if I need to adjust for the up and down...

I think I might bite the bullet and pick up the air gap. I think with the divider milled and combined with a 2" hvh spacer it would provide a good MAP signal for efi. Increased vacuum, torque and drivability. I always have the M1 on hand if needed. I've been going back and forth. I'm sure I'll...

I can't really find anyone that lists a decent stall for an OD lockup. Andre at edge said to call him, he lists a billet converter 28-3200 stall. He wants all my info to build. Hughes, PATC, Oregon all only show low stall speeds. I'm sure I can get one. I'm gettonly just getting to the trans...

So the only thing left to decide on my engine is intake manifold. Bear(bare) with me on this over asked question? This car will be 95% street driven. Maybe a 1/4 pass or autocross once in a while. But it'll mainly be a driver, cruiser and canyon carver through the mountains. So we'll start with...

How tall is that tire?

Just got my shipping notification.

They charged my account today and sent me info on proper head studs and bolts yesterday. Howard at trick flow has been pretty spot on with his timeline. Just like he said the website would show May for a ship date... Even though they would ship at the end of this week when they charged the account.

I'm looking for p/u 18343 for the roadrace pan.

18343

You should try ordering a milodon oil pick up? Ordered 3 separate times from different vendors. They all get cancelled, no one has an ETA. Tom @ Milodon has told me 1 month out on 3 different occasions. It's a never ending run around. Yet I bought the pan without issues? How do you produce more...

I just got a response from them a week ago saying end of March.

Man, I'm not sure where you are finding that price. The first page of this thread says 1100 each. 2200 pair. This thread says the same. Trick flow And also this:

I'm either welding in AN bungs or npts into the cam cover. I already tapped for npts but I may tig them. Block's in the shop and I forgot to measure before it left. I need to decide -12 or -10. I'm running Doug's which are smaller diameter. The passenger side is the only hang up. Need to see if...

Looks nice man. Should make insane numbers. Can you measure your header clearance from passenger center freeze plug to header tube for me?

Duane can you tell me what headers you are running. I'm doing this same mod but no way the headers cley on the passenger side that I can see. Can you show pics of your headers or mock up? Thanks

Does anyone have a copy of the cam card? Thanks, Keith

3000-7000 rpm on the placard in the pic.

I didn't even realize that. All I did was copy and paste my email. At least they are consistent on the release date.

I asked if they were still coming to market. This is the response I got from Oct, 5th. 'Hello, They are scheduled for release in late November early December. And Defiantly bringing to Market, Thanks, Howard Woodburn Trick Flow Sales/Tech Ph. (330) 630-1555 Fx. (330) 633-2504'

My favorite part. Hencho en USA