Search results for query: *

Can anyone tell me if the driveshaft is the same length whether you are using an 8 1/4 or 8 3/4 rear axle. If not, what's the difference in measurement? Thanks.....

Can someone give me the skinny on how to tell if a converter is for a 904 or 727? The second question would be does Lock up vs. Non lock up make any difference. Thanks guys...

I was reading on slantsix.org about guys having trouble going from a 1 barrel to super six because the kickdown linkages are different, and nobody thinks to take that when they source the 2 barrel intake and carb. One dude offered a great solution. He said mid 90s Dodge pickups used an...

I had a previous thread about the removal of a burnt 904 from my 87 D100. I picked up another 904 from a running 73 Dart ($60), and I'm putting it in. I have a few bolts in the bellhousing, and I'm now on to the torque converter. My concern is there seems to be a lot of space between the flex...

Here's the short course: 1. Bought an 87 slant 6 D100 with a bad trans - no 1st gear, fluid close to black....it moved just enough to get off the trailer and into the driveway. 2. Bought a 904 from another truck off craigslist from a seller I had bought from before with good success. It was...

I took out my bad 904 transmission and I'm getting things ready to try to put the replacement in, and I notice the old transmission has the extension housing seal with the rubber boot, and the replacement has a fairly new seal but no boot. Do I need to halt progress and get a new seal with the...

I bought an 87 pickup with a slant six and a bad 727. Looked all over and finally found an alleged good used one for $100. Started taking the old trans out this afternoon, and after getting the torque converter bolts out I realize it's a 904, not a 727. Am I gonna be in trouble in regard to...

I've been reading about the myriad of kickdown combinations that came with our cars. It seems the cable solution is best since it's adjustable. Problem is I want to keep it looking stock. My local Upullit has an 87 Dodge 3/4 Pickup with a stock intake and 4 barrel. Will that work in my 67...

I found a really nice 87 D100 with a slant and a bad 727. I'd love it to have it for dump runs and to haul my kayaks. Can I use the 904 I have from a 68 or so Valiant? I wasn't sure if I'd run into tail shaft problems, or possibly need to swap the input shaft from the driveshafts. I...

The base info is 67 Barracuda convertible, very mild 340 with 2.02 heads, a Perfomer and thermoquad. It'll mostly be used for rides to the beach (100 miles each way). I'm struggling with coming to a conclusion with the rear axle. Can you tell me what would be the best of the following 3...

Hey guys, I'd appreciate it if someone could guide me through the cogent points of replacing the pinion seal on my 7 1/4 sure grip rear. I suppose the first question is do I need to put a prybar in the guts somewhere to keep the pinion from spinning while I remove the bolt? Second, do i need a...

I found an 83 van in my local pick a part yard that has a small block and a 727. The question is if I pick it up for a future project, will I eventually need to find a different tail shaft since it's in a truck, or will it bolt up okay for use in my 67 cuda? thanks guys.... Ken in Pa.

I have a 67 Cuda with a slant 6. If I use the Schumacher mounts, do I need any other pieces to slide my 340 into the slant 6 K frame? I thought I had read somewhere that I need a V8 drag link, or could have oil pan issues. thanks for any advice you can offer. Ken in Pa.

I was thinking of starting to collect some parts for a future small block 4 speed project. My local U-pick it yardhas a mid 70's pickup with a V8 and a 4 speed. It got me to thinking. 1. How can I tell if this 4 speed has a granny low gear? 2. If it does, is it completely unusable for a...

Hey guys, need some advice in regard to rear end. The 8 3/4 A body rears are geting pretty expensive, and I need to swap to big bolt pattern anyway. My local U-pull it has a 90 or so Dodge pickup with a sure grip rear right in the gear range I need (I believe it was 3.21 or thereabouts). How...