Search results for query: *

I have an Offy 4 bbl intake I want to sell. $250 .+shipping . I take US Postal money orders only as payment NO PAY PAL or other forms of payment. Located in LI , NY

This 6 cyl linkage and Z bar was removed from a 6 cylinder 1972 Duster The short Z bar is for a small block of the same vintage. The linkage and longer Z bar is from a 1972 A body (Duster) that I parted out . $ 80 shipped in a flat rate box to the lower 48. I am located in LI , New York

I have two Holly 1 bbl carbs that are complete that I took off from a 1976 Dodge 225 that were in working order 3 years ago when removed. $75 for the pair , shipped to the lower 48 in a flat rate box. Located in LI , NY

I have a pair of Z bars and the linkage that works the clutch safety thing .The short one is for the 8 cylinder and the long one is for a 6 . $ 80 shipped to the lower 48. I am located in LI , New York I took the 6 cylinder one and the linkage out of a 1972 Duster

I have 4 2bbl Carters from 273's that I was working with years ago. They are all there but have been boxed up for a good 20 years. Located in LI NY $ 40 + shipping each or $140 + shipping for all 4 as a package

I have this old Carter 1bbl from a 1960 or so slant 4 sale . Located in Long Island NY . $50 + Shipping

I have a lot of various 273 linkages here for sale . $50 for all + shipping . Located in Long Island NY

I have these two Accel dual point distributors and a 64-66 273 kick down pivot that bolts to the back og the head for sale as a lot.The dists are in decent working condition .Both move freely and have minimum shaft play .The pivot is all painted and ready to go. $90. shipped to anywhere in the...

I have a set of 273 con rods I am selling . I want $25 +shipping .They came out of a running motor I scrapped years ago. I'm located in LI , NY

I am selling a new cast iron water pump for an early (64-66 ?) 273. I bought it for my 65 Barracuda but sold the car before I could install it . I am located in Long Island ,NY and want $75 + shipping

This came off a 273 I parted out a few years ago $ 20 + shipping . It should fit in a small 8 dollar flat rate box . Located in LI NY

This came off a 273 $ 40 + shipping Located in LI NY

I have a full set of rods I want to sell from a running 273 that had roughly 100000 mi on it .I scrapped it back in the 90's when no one wanted them. I bought it for the heads. $30 + shipping they are located in LI NY

I have two Accel dual point distributors for sale.They are in good condition and complete .$ 125 each + shipping Located in LI , NY

I have an incomplete set of new lifters for a 273 for sale There are 15 pieces new in the boxes .. $ 25 + shipping . They are in LI , NY

I bought this when I was restoring a 65 Barracuda and never used it.It's an iron water pump for the early 273's . It's new in the box with the normal shelf wear . $40 + shipping .It's going to be about 12 lbs packages and shipped USPS from 11743 so the shipping will be based on that. I'm located...

I have 3 sets of 273 motor mount brackets for sale at $40 per set + shipping from 11743 I will be removing the insulators so the weight won't be so bad. I'm located in LI NY

I bought this when I was restoring a 65 Barracuda and never used it.It's an iron water pump for the early 273's . It's new in the box with the normal shelf wear . $40 + shipping .It's going to be about 12 lbs packages and shipped USPS from 11743 so the shipping will be based on that. I'm located...

I have this 273 LA 3 speed iron bell housing taken out of a v8 3 speed 65 A body car. $100 + shipping. I'm located in Long Island NY 11721 . It's heavy so a local pick up would be best if possible. Also have some alum 6 cyl 3 speed bells & transmissions if there is any interest. 65's and 66"s...

This is a parts lot go 1964-66 A body 273 stuff . 2 2bbl air cleaners , 2 power brake vacuum cans ,2 8 cyl. gas pedal mechanisms , 2 thermostat housings , and a set of Barracuda trunk door hinges .I’d like $100 + shipping and all other fees associated with payment for it. Located in LI , NY USA.

I have 2 sets of pistons ,rods,caps,and nuts from some running motors I parted out way back in the day in the early 90's. $ 50 per set + shipping.

I have the whole set up for a 65 Valiant/Barracuda/Dart floor shifter I want to sell.It comes with the floor tunnel and brackets,2 full sets of cables,the shifter,and the small console . $ 450+ shipping

This came out of a good running 273 that my friend put electronic ignition in. It is tight spins free no side play in the shaft and complete. $ 175 + shipping .

This is a lot I'm selling.It's 65 273 stuff left over from a resto I did years ago on a 65 Barracuda. $150. + shipping. (Parts lot. Seller doesn't want to separate) edited by staff

I have the whole set up for a 65 Valiant/Barracuda/Dart floor shifter I want to sell.It comes with the floor brackets,2 full sets of cables,the shifter,and the small console . $ 450+ shipping

I have a 3743859 bell for sale. Was sold but the deal went south so here it is again.It is for the overdrive 4 speed trans with the 5.125 retainer and takes a 130 tooth flywheel. 185. + shipping.It's all packaged and to ship to Kentucky or Tenn.the post office wanted 30 bucks so depending how...

I have an A833 4 speed out of a 1968 Mopar A body in good rebuildable condition. All the gears are good and turn smoothly .It needs to be freshened up with bearings and synchros before putting it in. The build date 2531 is the julian date, Tuesday July 2 1968, 0201 is the production # that day...

Built this X pipe to use with these beautiful chrome Doug's Under chassis headers that I was going to use in this 65 Valiant I was putting a 360 in.Well,that was 20 years ago and that project got sold when I had to move so over the years I sold off the headers,the new MP flywheel,the bell,the...

I have one of those aluminum 3 speed 4 speed bellhousings for a small block V8 I'd like to sell or trade Part # 3743859 .I would trade it for the iron 6 cylinder bell #2468433 that fits a 1965 A body with a 6 cylinder 4 speed option or sell it outright for 200.+ shipping

I have a 68 A833 4 speed I want to sell.The case and gears are good it should be rebuilt with new bearings and synchros. It is an A body transmission was made in July of 68 so it may be right for a 69 or not .I’d like to get $600 out of it plus the shipping. A local pick up would be good for...