Search results for query: *

Looking for a clean driver 71-72 Demon,prefer H code cars but not a deal breaker if not. May aslo look at 71-72 Dusters. Would like to stay in the 20 to 25K range for price

Looking for a clean 340 4 speed Demon in a high impact color. Close to or in WI would be ideal.25 to 30K for the right car

Needing a good used 2 speed wiper motor, harness from it to the to the bulkhead connector,arm and the under dash linkage for a 1970 Swinger

Needing a 29-30 spline 727 slip yoke, just checking here 1st before I buy a new one.

Looking for a nice driver 4 speed car with minimal rot in the WI area. No 4 doors,wagons or trucks. Like to stray in the $8500 range or less

Looking to buy a 33-34 Plymouth Coupe that has already been rodded. So no original cars and I hate gold chainer cars with billet aluminum and pastel paint so real hot rods only

Looking for a solid 65 Dodge dart drivers side front fender. Must be willing to ship if not in WI

Looking for a 47.5" center to center on the u joints driveshaft and it can be the big or small u joint.

Looking for a good used pair of 70 Swinger hood scoops complete with bezels and all studs intact.

Ready for a new project.Looking for a 69-70 Dart factory 340 4 speed car.Must have solid rails and minimal rust.Again a project car so no done cars unless they are below my $8500 budget.I am in central WI so the closer the better. May consider Dusters and Demons as well.

Needing a good 742 center with a clutch type suregrip and 391 or 410 gears and must be willing to ship to Central WI zip 54962

Looking for my next project and wanting a 71-72 Demon or maybe a Duster.Some rust is ok but no complete rot boxes with bad rails.The closer to central WI the better.

I need the Plymouth name plate emblem for the valance or hood and it can come from a 68-69 barracuda,69-72 valiant,70-72 Duster,68-69 Belvedere.It can have a few pits but needs to be one piece and all 3 studs good.

Need a good upper and lower trunk lid moldings with fasteners for a 67 Barracuda Notch.They don't need to be perfect but not all dents and dings either.

Looking for some old school parts for a gasser project. 3 spoke with the holes in the spokes superior steering wheel black or green flake 14" Late 60s to early 70s B&M or Hurst forward pattern auto 3 speed shifter Aluminum type gas pedal with cable 15x7 or 8 or 10" aluminum slot wheels...

Need a good solid 360 truck oil pan with no rust.Truck is a 91 with a la 360.I can get a new one for $60.00 with free shipping so be real with prices

67 Barracuda,318 with a 727,edelbrock carb with aftermarket intake.I need everything from the carb down to the small arm on the transmission.

Needing a good 91 W150 4x4 360 oil pan.

Looking for a pair of usable BB fenderwell headers,dents are fine as long as the pipes are solid.What they fit doesn't really matter as the will be in a gasser type fat fendered car and will make them fit.

Looking for a used flat or 6 pack style fiberglass hood for a 67-68 Barracuda.Pin on or bolt on,either will work.I don't check these ads that often so PM me.

Need 1 useable SBP 10x1 3/4" rear brake drum

Need a driveshaft for a 67 Barracuda,small block,727 with a 8.75 rear.I have no idea what length it takes.

Looking for a set of 4 SBP aftermarket wheels for a 67 Barracuda.I'm not real picky so open to about anything with or with out tires.Must be willing to ship if not local to central WI.

Looking for a bolt on timing tab for a 67 LA 318

Need a nice 67 Barracuda drivers side door panel,prefer black but any color will work.Will take a pair if need be. Also need a nice pair of front arm rest pads for the same car in black but any color will work

In need of a LA 318 car oil pan and pickup Also I need of a good distributer for the same

Looking for a driver 2 dr A body.Open to about anything and a V8 would be a plus but not mandatory.Minimal rot with solid rails.The closer to central WI would be ideal.Looking to spend no more than $2500. I do have a 1929 Model A rod project that could also be used as trade material plus...

Looking for nice a driver A body,needs to be a 4 speed and have a V8 engine.Originality,F/T or numbers isn't a big deal and I don't want any rot box cars full of filler.I will look at anything but no 4 doors please.The closer to central WI the better but for the right car you never know.I rarely...

Looking for a complete running slant 6 with trans combo.Prefer as close to central WI as possible.Shoot me a pm if any of you WI guys have anything.

Looking for 4 aluminum slot wheels.I need either 4 that are 15x7 or 2 15x7 and 2 15x8 with around a 3.5 to 3.75" backspace and a 4.5" bolt pattern.Trying to steer clear of the unilugs but if need be they will work.