For Sale- 1975 Dodge Dart 2dr Project needs to be finished -
Car has been totally disassembled, all sound deadener and under coating has been removed, lower quarter panels have been repaired, both inner and outer. All other rust has been cutout and repaired. The underside of the car has been cleaned, primed, sanded and painted. It has the stock torsion bar front suspension with all new suspension parts. (Ball joints, linkage, etc.) The k-frame has had the engine mounts removed. The car has a 1970
model Duster 1 piece tilt front end it is mounted on the car. The rear package tray and firewall is installed. The rollcage and spring relocation kits and frame connectors were installed by locale NASCAR fabricator, he also fabricated a new trunk floor and fuel cell mount along with installing the wheel tubs.
8 point rollcage installed
Springs relocated 002 003 SS Springs
Weld in frame connectors installed
Custom trunk floor with fuel cell mount
Wheel tubs
All new brake system drums on all 4 wheels, 11 in the rear, 10 in the front
4.5 inch bolt pattern front and rear
Aluminum master cylinder
Line loc installed
#8 stainless fuel line installed
Custom fuel pump and spin on filter mount
Custom seat mounts
Rear wheel well openings stretched to the front 3 inches
Narrowed Dana 60 Truck housing professionally narrowed
All new Strange parts spool axles 4:88 gear All set up will just need to have the perches welded on.
Fresh BB 727- Turbo action reverse manual shifted valve body, 5.1 kickdown lever- good clutches and bands, upgraded pistons and springs
Deep pan
2 Turbo action Torque converters (New)
1 17505 1 -1 17805s
Freshly machined 383 block, .030 over
Line honed, decked cam bearings installed
Reworked stock steel rod resized, lightened, shot-peened good bolts installed
Speed pro pistons installed on the rods
Its all balanced
Fel-pro overhaul set
2 copper head gaskets
Engle hyd cam grind #K58H, 515 lift (3 bolt)
Engle lifters #862H
Engle springs #833
1 set bare open chamber steel heads, some porting done, but they need to be finished
PBM 3 bolt timing set #8606
Melling oil pump #M-63HV
Speed pro rings #R-9590-035
Crane push rods #64 672 -16
Hyd for adjustable rockers
Clevite bearings
MS 876 P.10
LB 527 P.10
N.O.S Accel Dual point distributor #37302
4 extra caps
3 rotors
3 points sets
1 cond.
1 super Coil (used)
2 Holley blue fuel pumps
3 Holley regulators 2 new 1 Used
16 Imperial electric fan 226116
2 driver F/X seats (used)
2 sets Crow enterprises 6 way belts (black 320004)
Mancini poly spool type trans mount #MRE 4422
Autometer 5 pro comp tack #6089 (used)
Cover lay dash cap #22-402
2 sets Isky adjustable Ductile iron rockers and shafts (used)
4 -15x10 aluminum wheels (used)
2 15x 4 Pacer wheels
4 185/80R 15 front tires
2 sets of MT cast aluminum valve covers (used)
2 universal drive shaft loops
1 set of Hedman headers #78030
1 C.E. Aluminum BB engine plate
1 C.E. fore and aft travel limiter
1 15 gallon fuel cell
2 new battery boxes
1 Master cutoff switch
Positive and negative battery cables
1 set BME 440 aluminum rods Checked and resized by BME (Used)
1 seven QT oil pan (used)
1 chrome Direct Connection timing cover (Used)
1 400 engine
1 383 short block
1 steel 383 crank
2 BB 727 transmissions
6 cyl. A-body radiator
2 complete sets of glass
Front and rear factory bumpers
Original front fenders
1 pair of 70 Duster steel fenders
Steel deck lid
73 and 75 model dart grille and header panel to match
Door handles, window trim etc.
N.C Title
Car is located in NC
Unless it says used or a factory casting etc. all of the listed parts are new and in the box
$6500.00 for everything
Plus much more.
For photos -
http://s861.photobucket.com/albums/ab179/jwmotors/1975 Dodge Dart/
Car has been totally disassembled, all sound deadener and under coating has been removed, lower quarter panels have been repaired, both inner and outer. All other rust has been cutout and repaired. The underside of the car has been cleaned, primed, sanded and painted. It has the stock torsion bar front suspension with all new suspension parts. (Ball joints, linkage, etc.) The k-frame has had the engine mounts removed. The car has a 1970
model Duster 1 piece tilt front end it is mounted on the car. The rear package tray and firewall is installed. The rollcage and spring relocation kits and frame connectors were installed by locale NASCAR fabricator, he also fabricated a new trunk floor and fuel cell mount along with installing the wheel tubs.
8 point rollcage installed
Springs relocated 002 003 SS Springs
Weld in frame connectors installed
Custom trunk floor with fuel cell mount
Wheel tubs
All new brake system drums on all 4 wheels, 11 in the rear, 10 in the front
4.5 inch bolt pattern front and rear
Aluminum master cylinder
Line loc installed
#8 stainless fuel line installed
Custom fuel pump and spin on filter mount
Custom seat mounts
Rear wheel well openings stretched to the front 3 inches
Narrowed Dana 60 Truck housing professionally narrowed
All new Strange parts spool axles 4:88 gear All set up will just need to have the perches welded on.
Fresh BB 727- Turbo action reverse manual shifted valve body, 5.1 kickdown lever- good clutches and bands, upgraded pistons and springs
Deep pan
2 Turbo action Torque converters (New)
1 17505 1 -1 17805s
Freshly machined 383 block, .030 over
Line honed, decked cam bearings installed
Reworked stock steel rod resized, lightened, shot-peened good bolts installed
Speed pro pistons installed on the rods
Its all balanced
Fel-pro overhaul set
2 copper head gaskets
Engle hyd cam grind #K58H, 515 lift (3 bolt)
Engle lifters #862H
Engle springs #833
1 set bare open chamber steel heads, some porting done, but they need to be finished
PBM 3 bolt timing set #8606
Melling oil pump #M-63HV
Speed pro rings #R-9590-035
Crane push rods #64 672 -16
Hyd for adjustable rockers
Clevite bearings
MS 876 P.10
LB 527 P.10
N.O.S Accel Dual point distributor #37302
4 extra caps
3 rotors
3 points sets
1 cond.
1 super Coil (used)
2 Holley blue fuel pumps
3 Holley regulators 2 new 1 Used
16 Imperial electric fan 226116
2 driver F/X seats (used)
2 sets Crow enterprises 6 way belts (black 320004)
Mancini poly spool type trans mount #MRE 4422
Autometer 5 pro comp tack #6089 (used)
Cover lay dash cap #22-402
2 sets Isky adjustable Ductile iron rockers and shafts (used)
4 -15x10 aluminum wheels (used)
2 15x 4 Pacer wheels
4 185/80R 15 front tires
2 sets of MT cast aluminum valve covers (used)
2 universal drive shaft loops
1 set of Hedman headers #78030
1 C.E. Aluminum BB engine plate
1 C.E. fore and aft travel limiter
1 15 gallon fuel cell
2 new battery boxes
1 Master cutoff switch
Positive and negative battery cables
1 set BME 440 aluminum rods Checked and resized by BME (Used)
1 seven QT oil pan (used)
1 chrome Direct Connection timing cover (Used)
1 400 engine
1 383 short block
1 steel 383 crank
2 BB 727 transmissions
6 cyl. A-body radiator
2 complete sets of glass
Front and rear factory bumpers
Original front fenders
1 pair of 70 Duster steel fenders
Steel deck lid
73 and 75 model dart grille and header panel to match
Door handles, window trim etc.
N.C Title
Car is located in NC
Unless it says used or a factory casting etc. all of the listed parts are new and in the box
$6500.00 for everything
Plus much more.
For photos -
http://s861.photobucket.com/albums/ab179/jwmotors/1975 Dodge Dart/
