Search results for query: *

What valve spring for Mopar Performance P4120231. It Is the 284* and .484 lift with 1.5 rocker arms. I will be running 1.6 rocker arms which should be .516 lift. I'll be using j heads but will be going to aluminum heads if the 10.9 compression is to much for cast iron heads. I don't see any...

Looking for backing plates and hardware for bbp . thanks

i have a 8 3\4 rear and changing to big bolt pattern and looking for brake parts for the swap. Are all bbp backing the same other than brake diameter? Is there different backing plates for the different widths? Will 1\2 ton parts work or do they need to be for a car? Any specific model? Any to...

I bought a part from a member here, and paid what I thought was a fair price. I got the part and its not what was advertised and it is rusted to the point of not being a useable part for me. I got it over a month ago and sent a message to the seller about the part not being what is was supposed...

Looking for a windshield in good condition. Could probably use a seal as well.

I recently got a Bradbury Series 40, 4 post lift from the 80s. It was in a pile in a barn and had a broken cable. I tried to find cables online with no luck and ended up have a local rigging shop make new ones. When I got the cables and started to set it up and some pulleys were missing. I...

Cast iron case. I had it in my car for a while and it worked good. Asking 450.00 plus shipping or pick up in Omak Wa.

I need a alternator bracket and the adjusting arm to fit a 65 D100.

Also looking for wheelhouse and trunk drop-off for both sides. Thanks.

Used in good condition. Doesn't look like its been modified. 500.00 obo shipped from Omak WA.

i have a set of 1970 440 manual trans. six pack carbs. These were taken off a running 340 engine about three years ago. 1000.00 plus shipping from 98841

650 cfm spread bore double pumper mech. secondary. hasn't been used in years would need a kit. 95.00 shipped from Omak WA.

4160 core 600 cfm vac. secondary, manual choke missing choke shaft otherwise looks like the rest of it is there. not froze up. 45.00 shipped from Omak Wa.

600 cfm vac. secondary elec. choke. It was working ok about 3 months ago when I went to a mech. carb. 125.00 obo shipped from Omak Wa.

Solid set of shields. No rust through only a few minor bends around the edge. 40.00 plus shipping from Omak Wa.

Commando air cleaner chrone is in decent condition. Has orig. base and aftermarket base. 125.00 plus shipping from Omak Wa.

I have a set of spindles for the Kelsey Hayes disc brakes. 75.00 ea. obo plus shipping from Omak Wa.

Holley List 4792 for 70-71 340 auto trans. I bought it a couple years ago as a new never used carb when I was trying to piece together a six pack. Dirty from sitting on a shelf. I don't believe it has ever had fuel in it. 250.00 obo plus shipping from Omak Wa.

Will a 66 sedan windshield fit a 66 hardtop?

Looking for a decent drivers side fender

Looking for a full drivers side quarter panel for a 2 door. Also need outer wheelhouse and trunk extension/drop off.

Looking for both sides

Looking for a six pack air cleaner set up in useable condition.

I have a new set of D450 headers still in the box I got them in only opened for pics. They run 879.99 at Autozone and 949.97 at summit I would like to get 600.00 plus shipping

I changed the transfer case motor yesterday on my 2008 Ram 1500 5.7 Hemi. That may or may not be part of it. After changing it I checked that it was shifting and it seemed to be working properly. I drove the truck about 25 miles and the 4wd low light started to flash on the dash. It flashed for...

'75 overdrive 833. Works good. I used it for a few months it was quiet and shifted smooth. 350.00/offer plus shipping from Omak WA

I have two bell housings. First one is a cast iron 9 1/2 in for 122 tooth flywheel. I cut it to use with an overdrive trans with 5.125 in bearing retainer. No cracks and all the threads look good. 100.00 plus shipping Second one is a 68 cast iron with 4.354 in. hole. No cracks and threads...

SOLD Six Pack intake in new condition,SOLD Holley 2300 350 cfm center carb never used 400.00 plus shipping. SOLD Performer RPM manifold used but nice condition SOLD Parts located in Omak WA

Spindles with dust shields. Rotors may or may not be usable includes one caliper for core or rebuild. can ship in two large flat rate boxes. 200.00 obo located in Omak Wa.

set of KB 190 pistons for 360. Standard size. Installed but never ran. 200.00 obo plus shipping from Omak Wa.