Search results for query: *

some Updates. The Shop guy was ill so I had to wait one week more. But they gave me an 600carb so I could Cruise. The old clutch broke down so I ordered the Cheapest from summit (poor student) It's from Zoom 10inch for 145$. After a Week it arrived Today. Now installed works great! Even...

After a couple of tests it´s now running. First I had water in the oil because of a leaking intake manifold gasket! Couldn´t had more Bad Luck: These Parts broke successively :rofl: Batterie Starter Rotor Cap Ignition Condensator Ignition Coil My 500 Edelbrock Carb is for a rebuild at a...

How do I install the timing gear ? Is this correct? slit in the gear has to point on the last intake manifold mounting hole at the head? http://vintage.mitchell1.com/PClubData/chassis/den73/V2D735025.pdf Check this file! Last article page 30/ First at page 31

Location is Reutlingen. about 30km to Stuttgart

thanks. Then I have to rotate it. Next Time i will install the Radiator, Grill and bumper. To make the cuda look more like s car :D http://vintage.mitchell1.com/PClubData/chassis/den73/V2D735025.pdf Check this file! Last article page 30/ First at page 31.

Thanks you :D Yes totally stupid but thanks god just the hood and right fender. Also Headlamp bezel. But have all together now. Heads are back on and the sh!tty left exhaust manifold. Also timing case and water pump. Just need to order a set of lifters before I can install the intake/carb. Is...

@nm9stheham : The pic is with filter car is more red. Thanks for the advices so far will report now in my car thread: South german 65 Barracuda restoration Cheers Fury

Want to bring this thread up again. Last season endet not very well for me I bumped the cuda a little at the front. Was my fault. Fender was at a body shop and is back on the car. A new hood is reserved for me and need a pickup at the other side of germany :mob: Started the engine job last...

yes, good eyes! its a fun rally for Classic Cars where You have to solve tasks and Challenges or collect items. it's Very fun and Fancy like Diving in the Open air pool for the roadbooks! its more for the petrolheads and Daily driver guys. Love the People where You can talk to at the campfire...

dropped the heads at the machine shop today. Removed the valves yesterday only a few need a little new grind in but the valve seals were broken. New ones are in the engine seals set:) will update soon. Also some pics :thankyou: Regards from germany :usflag:

i've read that You Need to Mill the intake, too if You Mill the Head more than 0.03 what a Little differenze. 0.010 and 0.0095:lol: why not Both the Same. guess the gaskets will make it. regards

:wtf:thank You 65val for the link. The adjustable Rockers Are on the way to their new destination Germany :thumbsup: Meassured the cc on all 4 heads today and proved what I suspekted. First the cc is more than Chrysler told us back then. Stock 65 Head 60cc instead of 57 and the 66 Head 65cc...

ok thank your all so far. my engine Projekt escalated quickly :rofl:

PM

thats Sounds so easy but Its not that easy to find a Set of heads here in Germany. also i Need the commando heads with harder valve Springs. for this Reason i bought the easier aviable 318 heads. if I find no heads or rocker Arms i will use hydraulic lifters and just Mill down. Are there any...

interesting Point but there are heads like the 2843675 ones which were on Both Engines 273 and 418. the bore diameter is only about 7mm more.also the valve diameterdiameter is the Same. only 340 up has bigger ones. there Are no adj Rockets on my 273 heads because someone Changed to hydraulic...

cam arrived this week so I installed it yesterday. also new timing chain. I organiced a Set of 318 heads because my old ones weren't the Same year with Different bolts at the intake Manifold. the rockers are looking much more robuster. also hard valve Seats. the Problem is more Volume so i...

okay thank you all very much :usflag: I Will order the cam and report. cheers and regards from germany

thank you for the offer. The Cuda rings only 2 screw holes on the inner side. And a edge on the inner surface. Yours look a bit different

bringing this theme up again because wintertime is tooltime. :) Planing to replace the cam. installed the edelbrock d4b manifold and a 500cfm carb on my stock 273 a few days ago. But with stock cam the gas consumption went way to high:realcrazy: Also wanted to set valve lash but found out that...

picture is from the Web.

thanks for your fast replies so far. its the right headlight Bezel Infront of the light for a 65 cuda the set on eBay is also damaged too and way to expensive in my opinions. regards from Germany cheers Fury

Bumped my barracuda today and need help of my fabo buddies:thankyou: Need one trim ring for my right headlight in ridable condition (no big dents) need shipping to my location germany. Impossible to find here! Paying via paypal no problem cheers fury

Auto World Plymouth Barracuda 1964 Grey 1/64 64032B

I´ve ordered mine on eBay...

thank you for the article cuda :thumbsup: mine is now july 71 :rofl:

Yeah that would be helpful. Does someone have pics like that?

Thank you guys! Now installing RPM Meter and some electrical jobs with the lights for germany

Bringing up this thread again. Has someone an Old magazine article or advertising? Like this: PRESS Have to prove that the wheels were available before 1975! Thank you Regard from Germany

finally !!! Paintjob is done. I`m happy with it: