Post a smallblock 10.00 and quicker combo

-
uhhh even I saw the "stickied" post above referencing these builds. :)
 
No there is not--Small block ONLY,Di you read the title?????? Thanks Steve
 
std block 408 indy heads small solid roller cam 3550 lbs and a little spray full street trim .1.37 60 ft 6.0 @113 . 9.57@142
 

Attachments

  • 1170694_10151819051857485_1528672993_n.jpg
    66.3 KB · Views: 645
ian said:
std block 408 indy heads small solid roller cam 3550 lbs and a little spray full street trim .1.37 60 ft 6.0 @113 . 9.57@142
Click to expand...

Do you mind sharing how you built the cal trac
 
408 1970 360 block, Indy 360-1 heads, N/A, 3060lbs race weight with me in it, With throttle stop 10.05 - 10.20's at 131mph without stop, 9.75 at 139mph but got warned because i did not have licence. I know there is more there only had T-brake set at 3,500 rpm.
 
For sure check the stickey up top. It is stuck so it will never get buried and lost.
It is not a small block only thread but all engines running 10 or better. There's time zones listed. It was made a sticky soneverons can look through it and find something they like.
It'll allways be there. ;)
 
Screw the big block guys post it up here!!


I'll keep to myself (stands in corner and whistles)
 
Stock block 340 with 3.79 mopar billet crank (394 ci) 360-2 heads ,10.9 comp. 255/266 solid roller, pump gas 662 hp/ 533 tq. with 1050 Dominator.
Only ran a 6.29@109 with 1.33 60ft. at 2950 with a untuned 950. I believe that is around a 9.80-9.90 in 1/4
 
Swifter, sorry I was not around to "chat" with you. You have seen my combination run. Many may not have. So....4" stroke 4.150 bore R-3 block. CP pistons, Eagle rods, roller, cam .770 lift, 278/284 T & D rockers/push rod oiling on Brodix Heads, Super Victor Intake, 1050 carb, MSD, crank trigger, 904 6200 stall converter, Dana 60. Car weight: 3025 w/driver. Best runs are 9.59 & 9.58 @ 138 & change. Consistent runs are in the 9.60's to 9.70's all summer long. [this is with race fuel 112 octane] and 34 degrees of timing. Also a vacuum system is used and the ring package also was selected for the vacuum pump equip engine. Axle ratio: 4.56 with 32X14X15 Mickey Thompson "stiff" side wall tire. 60's are in the low 1.30's to and occasional 1.29-1.28 but not too often. The average 1/8 mile is 6.05 [cool weather] to 6.12 [summer weather]@ 111 to 113 And that's all folks!
 

Attachments

  • Dart GT with wing and wheelie bars 2013.jpg
    37.2 KB · Views: 302
  • DSCF2261.jpg
    31.7 KB · Views: 277
  • DSCF2284.jpg
    59.5 KB · Views: 278
  • Milan Dragway view in back corner.jpg
    42.8 KB · Views: 311
[ame]http://youtu.be/uUvHBOBhIto[/ame]








408 LA with Indy 360-1 heads, T&D rockers, solid roller, tall filled, TTI 1 7/8" headers, 12.5 to 1 compression, S & W back half, RMS alterktion, Strange ultra hd 9 inch with 456 spool, Reid race power glide, race ready at #2510.
Shake down runs between 9.5 and 9.7 at 138 mph
 
Beautiful car Mr. Eppler!

R3, 4" Molnar crank, 6" Molnar rods, Crane roller 264 @ .050 .750 lift at retainer. Jesel 1.6 rockers, W8 heads (B&H Perfprmance), Mopar 598 4150 intake, BG 750 cfm 4150 carb, 70 Duster 2980 w/t driver. 5 passes 9.64 @ 141.8. ....more to come!
 
Rob Eppler said:
Swifter, sorry I was not around to "chat" with you. You have seen my combination run. Many may not have. So....4" stroke 4.150 bore R-3 block. CP pistons, Eagle rods, roller, cam .770 lift, 278/284 T & D rockers/push rod oiling on Brodix Heads, Super Victor Intake, 1050 carb, MSD, crank trigger, 904 6200 stall converter, Dana 60. Car weight: 3025 w/driver. Best runs are 9.59 & 9.58 @ 138 & change. Consistent runs are in the 9.60's to 9.70's all summer long. [this is with race fuel 112 octane] and 34 degrees of timing. Also a vacuum system is used and the ring package also was selected for the vacuum pump equip engine. Axle ratio: 4.56 with 32X14X15 Mickey Thompson "stiff" side wall tire. 60's are in the low 1.30's to and occasional 1.29-1.28 but not too often. The average 1/8 mile is 6.05 [cool weather] to 6.12 [summer weather]@ 111 to 113 And that's all folks!
Click to expand...

Very nice car!

What is the Recipe on the 904? Most would say you are well over the power limits of running a 904 transmission!
 
I'm curious what made you go with the Brodix heads? Don't usually see them used
 
I have a few cars to throw in here..

68 Cuda
408
12.7 comp
Iron hogan w2 heads
Solid roller

9.78 @ 141


Next is a 225" mike bos hard tail

358
10.7 compression
Iron baton w2 heads
solid roller

A little bit of nitrous

7.21 @ 188
 
4in Callies with 2in rod journal
4.185 bore flat top
Coleman/Arrington W8 head 2.18x1.625 titanium valves
done by Brett Miller
[email protected] .455 lobe 110ls
T&D 1.7 rockers
420 intake with a Dominator flange
comp is 15.4
6.30 Carrillo rod
Bob Book Carb 1250+cfm

__________________
70 Plymouth Duster
440CI W8 SB Mopar
Powerglide 1.80 gear
60ft 1.28
5.70's 1/8@118 mph
9.20's 1/4@145 mph
 

Attachments

  • IMG_20140607_191237_116.jpg
    30 KB · Views: 197
I have seen Rob's car in person and watched down the track--It is a thing of beauty pic's don't do it justice !!!!!! Steve
 
You must log in or register to reply here.
-

Back
Top