Recent content by BoredandStroked

Is that a good headlight bucket on the drivers side I see, if so PM me. Any headlight rings or other buckets would be appreciated also

7 inch buckets/rings? Consider them sold if yes

I am sorry to hear about your father, hope everything is OK with you and the family. Do a good job at freshen that Scamp up! Merry Christmas and a happy belated Thanksgiving!

Hughes Performance stock replacement rings and bearings http://www.hughesengines.com/Index/products.php?browse=category&level0=U21hbGwgQmxvY2sgRG9kZ2UgTWFnbnVtICgzLjkvNS4yLzUuOSk=&level1=UGlzdG9uIFJpbmdzIDUuOUwgKDM2MCk=&level2=MS41MG1tIC8gNC4wMG1tIChTdG9jayBSZXBsKQ==&partid=27817...

Had to chime in on this one after reading, a few things. Did a wet and dry compression run on an engine a few days ago for a guy with some of the highest readings I have ever seen (on pump gas) at 245 psi (dry) on all cylinders with a variable of only 5+/- psi. Engine had 3,000 miles, ran on 87...

Hey man, how has it been going for you? As far as me a lot has changed to say the least. I moved to Alabama in 2011 for work. The Dart and 300 are still in WV sadly, hopefully going back this spring to get them!

That looks good, I have the same wheels on my 96 Ram haha. See if you will have enough ground clearance in the front if it was 5 1/2 to 6 1/2 inches from the ground. That would be a sick ride, I like re-using factory stuff so I hope it all works for you!

Hey guys and gals, I need some help with my 1996 Ram 1500. I am doing the conversion to 3 inch wide springs, off of a 2500. The last item that I need is the shackle bushings. I can not find them for 3 inch wide springs. I am praying someone that has a 2500/3500 tow rig has done this before...

Like most of the guys have said they suck! I have worked on many cars and now I am working at BMW where we have sunroofs, moon roofs, and panoramic glass sunroofs. All of which are a pain when they break. I personally don't like them because of the road noise with or without it open, lack of...

Yes the K1 crank is fully forged with honda rod journals, measuring 1.890". They also make a 4.180" crankshaft I believe that has a chevy type rod journal size of 2.000". The K1 crankshafts sell for 695 at Campbell Enterprise.

Here, hopefully soon, I will be possibly be using the K1 4.250" crankshaft in my 5.9 magnum. Not to sure on how such a long stroke is going to affect the piston riding in the bore or something else catastrophic. Need to find rods and pistons to go with it but like I said hopefully soon I will...

dustermaniac is right NC is harsh but the lawyers are very good at what they do haha. I got many tickets in NC but only 2 points and countless dollars. In virginia my first ticket was 105 in a 45, did the usual, pulled into a driveway as soon as I could slow down and waited. Police officer...

Your right about the suspension. Some types of parts can be used in both and some can not. As far as the how to work the clutch on the street, well, all depends on the vehicle and driver. Need to get to know how the vehicle will react with a certain parts added, powerband of engine, lots of...

check oil level and see if it is similiar, if so you have the two mixing somehow. head gasket problem can be checked by a tech at the local shop using a number of different ways.

Hey guys, nice to be back as a couple of you havent seen me around in a long time. I have a question about a transmission I came across at my parents house. My mother explained to me that it was a 4 speed that originaly came out of my fathers D-200 p/u. The only numbers I found on it was...