Search results for query: *

  1. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    Will do. I actually ordered them thinking it had that in there, and might need to adjust the clearance. . Got all but one, didnt order the smallest.
  2. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    So it got real hot. Another thing I found That clutch pack has a very flat wavy retainer clip, and not a flat selectable one. The trans date is July of 1970. Unless someone shaped it before me, that is not right for the year
  3. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    Did you see the picture of the Not Flat steel plate? I'm thinking you were right that it dropped the first clutch off . But I would expect the splines on the inside edge of the friction to show damage.
  4. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    This is a flat one. The next one up.
  5. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    Hers a problem. The bottom steel is not flat.
  6. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    Thanks, Jegs has just the 71 and up kits. The clutches and front band should be good I think. Gaskets should be the same. It doesn't come with the low reverse band, have to get that separately. Transparts warehouse has the metal thrust washer I need. Maybe I'll just order everything from them...
  7. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    Can anybody tell me what's different In a 1966 -1970 rebuild kit, and the 1971 and up?
  8. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    Funny how the plates are worn. Smooth on the outside edge, and rough on the inside edge.
  9. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    Wouldn't the splines on the clutch disk be torn up if it slipped past?
  10. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    I did not check the end Play before I disassembled it. I should have. I was planning on getting the plated metal thrust washer to replace the broken one. The broken washer was still on the shaft. Not sure how it stayed there being half of it was missing.
  11. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    The diaphragm spring is what was hitting the planetary
  12. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    Yes, that's what cut the planetary.
  13. Mopower71

    Lost reverse, need help finding it. 727

    But, but , but, the recommendation was to run type f.
  14. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    I also have this posted over here Lost reverse, need help finding it. 727 With the rest of the story
  15. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    Thing is. I don't want to put new clutches,steels, and bands back in to have the same problem. Side note. I sent the converter back out to ati today to be gone through. I want to make sure it is OK also. Ati calculations were over 17% slippage. There was no bad clutch material in the pan when I...
  16. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    Yes, thicker steel plate was there at the bottom. Yes it seems the contact on all the others was only 2/3's to 3/4
  17. Mopower71

    Lost reverse, need help finding it. 727

    Thanks. Maybe sat to long, 14 years since at track 11 years since on the road. No antifreeze in it. Moisture? Car has always sat inside, but has been dormant a lot of the last few years. Now I have the time and a little money to get her going again. Fuel prices are headed up. Ugh.
  18. Mopower71

    Lost reverse, need help finding it. 727

    What would have been done wrong to do this?
  19. Mopower71

    Lost reverse, need help finding it. 727

    Washer goes here. Half missing and I pulled the trans all apart and never found the other half.
  20. Mopower71

    Lost reverse, need help finding it. 727

    I will tomorrow. Have to pull the clutches back apart. Reassembled them so they didn't get scatered
  21. Mopower71

    727 one bad clutch plate. Input to output washer half gone

    Need some help. I don't want to just put clutches in and have this happen again. Bigblock 727. Rebuilt years ago,red alto clutches, kolene steels. all new bushings, thrust washers, both bands, cheeta manual reverse valve body, not a lot of time on it, 50 miles at most, and a few 1/4 mile...
  22. Mopower71

    Lost reverse, need help finding it. 727

    Need some help. I don't want to just put clutches in and have this happen again. Bigblock 727. Rebuilt years ago,red alto clutches, kolene steels. all new bushings, thrust washers, both bands, cheeta manual reverse valve body, not a lot of time on it, 50 miles at most, and a few 1/4 mile...
  23. Mopower71

    Lost reverse, need help finding it. 727

    I should. And I probably will. It's a pain. And I either fight with it around the headers or take them loose, which is also very fun. Mabey next year I will run it again.
Back
Top