Search results for query: *

  • Order by relevance
  1. bcschief

    1964 Plymouth Barracuda Door Latch assembly

    You might want to buy complete door assembly's and use all the guts and glass and sell the door shells when you're done. You live in a good area for salvage yards, but you may want to post a wanted add here and see what is close that won't cost a mint to ship.
  2. Bossanova5

    [SOLD] A Body Leaf Springs #3400072

    What are these out of? Thanks
  3. T

    Intermediate Shaft Wear

    Your gear doesn’t look nearly as bad as ours did. You caught it pretty early it appears. I’d definitely be cutting the filter open to have a look and that would determine if a bearing check was in order. Maybe run it a short time with a new oil change and compare the oil pressure to what it was new.
  4. Ricks70Duster340

    Valve adjustment.......

    Funny! My dad showed me to put a screwdriver onto the tip of the stud and the plastic part of the screwdriver in my ear. If it clattered, tighten it up a smidge until it stopped. Worked for me!
  5. J

    [WANTED] WANTED;....small block 273 DUAL Point Distributor

    i've got two 340 units that will work. PM sent
  6. racerjoe

    Hemi Swapping a perfectly good 70 Duster

    It runs! My gates heat shrink hose clamps didn’t show up so I could run it for very long. I put 2 gallons of coolant in it and it still isn’t even up to the water pump. That was enough for me to run a couple minutes. That single big throttle body sure makes throttle response snappy. It’s pretty...
  7. pauly

    1969 Race Dart w/ 426 Hemi- garaged for 45+ years

    Where’s the ❌?
  8. 4

    Oiling issues

    New to the group. I have a Dodge Dart Sport race car. 440 .055 over, 11.5:1 compression, Eagle stock stroke crank and rods, 6 qt oil pan and high pressure pump. Older professional products billet oil filter with stainless steel cartridge. Last year I lost oil pressure and spun a couple bearings...
  9. 66fs

    Valve adjustment.......

    LOL even a slant six guy can do it. Did it that way since I was 19 and that was a long time ago. Did it that way at the dealers on a major tune up through the 70's. We are talking stock interference adjusters, not adjusters with lock nuts. Yours and my idea of a "decent engine" is probably...
  10. MOPARMAGA

    1969 Race Dart w/ 426 Hemi- garaged for 45+ years

    More pictures please, thanks !
  11. physixx

    [FOR SALE] Fabricated polished aluminum valve covers for the small block LA engines with breather

    I have for sale a pair of what looks to be, Top Street Performance fabricated aluminum valve covers for the small block LA engines. These valve covers have very little run time on them are near perfect. Included is a PVC valve for the one side and a Mr. Gasket push in breather, P/N 4029G for the...
  12. 273

    Does this prove David Vizard's 128 lsa formula ?

    Any details of the parts and work put into it and it's performance ?
  13. MOPARMAGA

    Getting faster over here too finally.

    I am not familiar with the 480 cylinder head from Indy what is different from -1
  14. HR5058

    G3 in 64 Valiant update

  15. H

    Does this prove David Vizard's 128 lsa formula ?

    I didn't build I just ruined it. It was the 360 with 302's. It was a real eye opener.
  16. George Jets

    Got a new Truck (new to me)

    OK working on the engine bay wire harness to get basic things working. Computer is plugged in and main power lead at the battery is plugged in. Found one power keyed wire to feed the engine bay components and start keyed circuit. Auto Shutdown Relay Plug has the power feed wire to run it all...
  17. N

    Does this prove David Vizard's 128 lsa formula ?

    The piston absolutely positively has to come out of the deck. I will check it when I start putting my junk back together but IIRC they are .054 out of the block and IIRC that's about .040 deck clearance. As a general rule I don't go any closer than .040 because after that, any gains and...
  18. HR5058

    G3 in 64 Valiant update

    So far…
  19. Brooks James

    Will my 360 cast crank, cast piston……

    Get some good head gaskets
  20. Dew

    [WANTED] overdrive a833

    I have a 1:1 4 speed if you’re interested
  21. B

    Polka polka nights

    This part of Texas is/was a large German community. Fredericksburg still has Octoberfest and New Braunfels has Wurstfest. Lots of traditional music, beer and food, but the traditional “dress up” is pretty much the folks running the events. The Fredericksburg AM radio station (KNAF) used to...
  22. N

    Intermediate Shaft Wear

    You can look at it if it makes you feel better but as a very general rule, the pieces that come off a brass gear are fairly big and not small pieces. I'd start by cutting open the filter and see how much junk is in it. That should at least give you a general idea how much of that brass is...
  23. 273

    Does this prove David Vizard's 128 lsa formula ?

    Do you use pistons with quench pads ?
  24. N

    Does this prove David Vizard's 128 lsa formula ?

    Yup. The Chrysler open chamber has to eat a lot of **** from guys who don't have a clue just how good that chamber is. I expect my engine to be in the 28-30 range and maybe, maybe 18 initial. It may take less initial
  25. 273

    Does this prove David Vizard's 128 lsa formula ?

    What's the best combo you have built ?
  26. Icetech

    Stop in for a cup of coffee

    they are straight, pics looks off though
  27. dukeboy440

    Stop in for a cup of coffee

    Looks fine width wise. Are those pulleys in line or offset just slightly? Cant tell
  28. migsBIG

    Will my 360 cast crank, cast piston……

    Yes, the goat pee they pass for gasoline out here is pretty bad and was thinking if I kept the boost under 6-8lb range, I could get away with it. I am thinking it might even be better to put the assembly on a 5.9 magnum crate motor as not to have to worry about the cheap parts. Sadly, with the...
Back
Top