Search results for query: *

Great post

Yup solid lifter.

I wondered why I hadn't got one in a while.

With different compression ratios being brought up, what would be a good dynamic compression ratio for the 360 with a 4 barrel carburetor? It will be a daily driver and will need to be pump gas friendly. Cam, I don't know how to match that with the dynamic compression ratio.

Diamond Back I Red Line 165/80R13 Tires | 16803NKRL | 165 80 13 Tire Diamond Back I Red Line Tire 165/80R13 - IN CART DISCOUNT! Lots of 13 tires here...

I cannot disagree. I've used the Lucas Hot Rod literally for YEARS and have had no issues. I've also used a lot of the Lucas products and have friends who run professional repair shops that use it too and they all agree the products do what they say.

Some trucks still use leaf springs though so your snide comment is pointless. We still use aspirin. Paper maps will always work when your GPS on your phone craps out. Ratchets and sockets work long after the cordless tool battery loses it's charge. Progress doesn't replace everything. Print...

Exactly why I'm hoarding a pile of it. lol

Yunick13 - I assume you are subbing these picks in for your TF and FC 'locked' picks for the Route 66 Nationals only. Please advise if not correct.

Yes sir! It certainly appears to be a solid lifter! Nice work!

see: Website Help & FAQ

ABSOLUTELY. That is GOOD advice. I have seen many car shows on TV where they clean out mouse mess without masks or gloves. That is not very smart.

Just because something is on YouTube, that doesn't mean it is true. I don't use oil additives, but I certainly would not let one internet video convince me that they were bad.

I get a notification..."you have reached your limit (15) conversations, Question...How do I delete these conversations? I need to start a new one with another forum member. Norm

Yep.

Ouch, pricey.

I think I agree with @GTX JOHN when he says the spacer may not be needed. I have a 69 Barracuda with a 340 built to about 375 HP. It has an Air Gap and an Eddy carb, and I don't have any fuel boiling problems.

Ah, nice.

Honing blocks at 'operating' temps makes SO much sense to me.

That's your garage??? Wow! I'll fly you to Kansas if you'll help me get to looking like that. Seriously, It is VERY nice.

Yeah the transmission will physically bolt up to the engine, but my biggest question/concern is going to be the flywheel/clutch setup as Dion mentioned. Dion, I found your thread yesterday about the idler arm interference. Fortunately I wouldn’t have an issue there since I’m running an HDK in...

$600 shipped in the lower 48.

What is the narrowest 14" wheel I can get in the 4.5 bolt pattern? Thanks in advance.

Only one I know of has a thread on here and swapped the front plate, tail housing and main shaft so he could use an LS (I think) bellhousing. Not really what you are asking. The PS starter will cause issues, idler hits the starter hard. There is a fix, but it isn’t off the shelf. I have a...

I have the same head unit in the Valiant and it sounds really good. It's also insulated with Killmat. The truck is a truck. Old and loud. As for the speakers, they are all I can afford. Feel free to send me a better pair.

Amen to using a long board (sanding block). I probably spend at least 100-200 hours block sanding filler and then high build primer on each and every paint job. I block filler lightly with 120, then 220. Then I spray 3 coats of Evercoat G2 (that's all I use). Then I apply black guide coat and...

The Gen3 hemi and small blocks share the same bellhousing pattern. Does that answer your question? All the other details I don't know, but it should bolt up. You gotta figger out the rest. lol

Member ir3333 I believe has one. He's located in Sterling Ontario Canada and I can't imagine what Shipping would cost ??

Has anyone here put a tr6060 from a Challenger behind a small block? Will the stock bellhousing work (I know the starter is on the passenger side) or will a different bellhousing be needed? Thanks

here's the stuff new: https://www.moparmall.com/Slant-Six-Manifold-Mounting-Hardware-p/325-005.htm if somebody doesn't come up with a set for ya, shoot me a PM. i'm sure i have some, i'll just need to root around a bit for it.