Search results for query: *

Or ask someone here with the same engine/trans setup to measure their rod, For the "Kickdown" not the other "rod" No puns.

Pictures are always needed and appreciated on these types of questions.

Do you have a FSM ? It will have pictures of the linkage set up and adjustment procedure. Link: Service Manuals – MyMopar

Nice looking. Good thing the tires are extra load for that size.

The rim will have a DOT approved and the brand cast into the wheel. It will bee around the center part of the rim so it doeswn't interfere wwith stick on wheel weights.

The rim will have a DOT approved and the brand cast into the wheel. It will bee around the center part of the rim so it doeswn't interfere wwith stick on wheel weights.

You never said what look you want. With that wide of a wheel, it will generally be a reverse or very negative offset. This will not clear a stock with rear axle at factory height without rubbing. So either you will need a higher arch rear spring setup and longer shocks or a narrower axle to...

I would look in the FSM.

Bruce from @ns1aar does them. Home So this is for the motor, however the wires from the switch should essentially go to the motor except for the power in. MOPAR 3 SPEED WIPER MOTOR BENCH TEST High Speed Connect jumper wire from motor case to battery ground Connect second jumper wire from...

:rolleyes:

:welcome: aboard. Pictures please.

Is that like wanting to take a bath without taking your clothes off ? Seriously, you really need to take it apart to get to all of the areas to do a thourough job. That stuff really gets hard and is not easy to clean. Brushes, picks, solvents... no easy solution.

It is HOT, HOT ,HOT !!! Please keep cool and safe this Summer.:thumbsup:

Remember to always check in Neutral and the proper level is abpout 1 pint below full. Happy motoring. Info will be in your FSM. Free downloads available here : Service Manuals – MyMopar

We are caught up and have a good supply of freshly made parts for our Mopar Door Hinge Restoration Service. New parts maker, slight price increase. Here is a copy of the current 07/01/2024 Member Price list. Thank you for your business. Contact me if you have any questions...

Ditto. Replace all lines that are not new. Get a new T-fitting. Rubber and steel. Brake lines like coolant hoses go bad from the inside out. Any crud that was in the lines will now be in your calipers and wheel cylinders . Always flush/replace lines BEFORE you connect to new calipers/wheel...

Has to be leaking somewhere. If you can't see on top you have to look underneath.

When you have tubes, the tube acts as the plug seal. If you don't remove the crush sleeve, it will leak because it can't seal to the aluminum tube, only a steel/iron seat. Like double gasketing an oil filter, a big leak. If your oil was burning you would have a lot od blue smoke, fuel will...

Install new plugs, remove crush rings if they have them on heads with tubes. NGK3459/ZFR5N is a good plug for these. Any seals that are hard must be replaced. They are no longer seals but leakers. I hear tht a good source for info on these is @slantsixdan

nope

Sit the tires on a hot surface instead of melting the tires.

Fuel can only burn so fast. That is why the ignition has to have advance to go faster. But you reach a point where the next cylinder has to fire. The reason that the cars go faster now is not based on power, but tire traction and clutch slip.

Moparts on the Web - Main Index Pinion & U-Joint Angles

How to test a 3 speed wiper motor MOPAR 3 SPEED WIPER MOTOR BENCH TEST High Speed Connect jumper wire from motor case to battery ground Connect second jumper wire from battery positive to BROWN lead Motor should run on high speed continuously Low Speed Connect jumper wire from motor...

@ns1aar is a member who has ben rebuilding those for over 25 years. He has a post somewhere on the site of how to test it. I will see if I can find it for you. Home

To me they are rebuiladable cores. Cut the price in half and I will take them. Thanks Leo

Jerry West was one of the first new players of the LA Lakers when the moved from Minneapolis. The Lakers name came from the Minnesota Lakers, "the land of ten thousand lakes " is Minnesota's motto. Way before Chamberlain, Goodrich etc.. and they played beside him. West came to LA when they...

Stock upper A-arms are cheap if you need to just sacrifice it.

So you got the nut off but the rest of the bolt wont come out of the bushing sleeve ? Disconnect upper ball joint from spindle so you have full range of motion on the upper control arm. This will give you more room to work. May be time for a torch to burn the bushing out and loosen the rust...

Try to get non needle bearing typr if you do. Bronze bushing type have less issues.