Search results for query: *

I think you have to put it in a for sale section. Tom

If you are going to run 8 psi, you should probably lower the float level slightly [ 0.030" ]. Raising fuel pressure increases the fuel level.

I've got none of that!

Finally, Hysteric, you did something right...... lean mixtures need more timing, which is why when cam overlap increases, the mixture is diluted [ leaned out ] at lower rpms by exh dilution...& requires more timing. Many years ago, Champion had a spark plug series called the U series that had a...

And be finished by the end of the week.

Here is the plug wire test. #6 was a non-res plug, specified by the wire manufacturer

I've owned this one for 8-years an just now finally starting to work on it. Tom

Here is what NGK really said about resistor plugs......

Hysteric, Are you really that ignorant? Engines using a distributor have a rotor that has an air gap that the spark has to jump before it gets to the spark plugs. That air gap has a resistance in the millions of ohms, several orders of magnitude greater than a 5k resistor inside the plug. In...

I've been using 15x7 Wheel Vintiques for years with no problems, just put them on torque them down. Never really thought about it.

Welcome aboard! This is the welcome wagon where you introduce yourself, show us your car(s) and tell us about it or them. You will need to go to the classifieds and post a wanted thread. The moderators may delete this thread, because wanted and for sale ads are against the rules in the general...

We have a member here who offers reproduction lenses for a lot of our cars. I believe his screen name is @Mexican Spec I tagged him so maybe he will chime in.

I have used contact cement [ glue ] many times. I must have been lucky.....

I ran across these new taillight lenses on ebay motors for less than $80 delivered https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2499334.m570.l1313&_nkw=1970+Dodge+Dart&_sacat=6028

OP: re the first photo in your first post. Every rallye wheel produced by Chrysler has this inner and outer ring mounting arrangement. Its been working fine since 1970...

The factory Prospector Hurricane wheels look dang good.

Last time I lived in Virginia, I was working dayshift as a defense contractor, I couldn’t find a swingshift permanent job. Congratulations on your dayshift.

Need a picture of your printed circuit board. There should be three slots where the IVR plugs in.

I've seen Holleys stand 10PSI. They can usually stand more fuel pressure than say a Carter or Edelbrock.

If it wasn’t important Holley would say5-8psi is fine….. but they don’t

no check valve. You seem to have a vent system that is older than your car. up through 1970 the vent was simple and ended inside the rear frame rail. it is actually design not to vent anything out of the tank, but rather let air into the tank to balance the fuel being pumped out. 1970 CA cars...

That's what I thought, all the carsI was getting steel wheels off of for guys who wanted that look. I should have kept one of the trunk release for my self, but I had had my stock one replated so never. I may be a cheap old SOB. Like stated above gold diggers. I like to pay fair prices, and...

Picking one up in the am from a.member

Still available and a quality piece!

Over 100 pairs of heads! Found one #286 1963 Max Wedge 426 Head =$475.00 Looks to be in nice shape!

I believe the trunk floors are the same 67 to at least 72 so I think all A bodies use the same frame rails so that shouldn't matter. I am only going to be changing the rearward most part of the quarters and yes I have given consideration in needing to incorporate the side markers as part of the...

E-383 HP engine 906 heads 10/23/68 Mileage unknown. Turns over. No carb or exhaust manifolds. Located in Western Maryland $750