Search results for query: *

  1. Inertia

    Installing engine mounts/motor mounts to the engine block

    OEM - 7/16 fine thread, center-lock nuts .
  2. Inertia

    Power Disc conversion/ proportioning valve question

    When the lite came on, pressure had been lost on one side/system. Opening fr bleeder and lite going out equalized pressure to zero, lite off, - secondary system (rear) failed as pedal went to floor, - if properly bled ! Lite staying on indicates shuttle is already triggered to failed side...
  3. Inertia

    Clutch Pedal Assembly Questions

    Bending the "stop" outta the way allows the pedal to move in a manner that allows the overcentre spring to be removed without the "washers/spacer" method of stretching the spring. Instead of stretching spring, just move one of the ends/anchors closer, by moving the "stop". There are 2 or more...
  4. Inertia

    63Dart Zbar issue

    Here's a link to Brewer's trans parts. They offer great advice, and you might see something that'll help you. There's a banner on site of a family death, so response may be slow. Good luck, https://www.brewersperformance.com/select-by-category/?cat_id=71
  5. Inertia

    No Electrical working

    Clean your battery terminals and cable connections . Particularly the Positive. Start there.
  6. Inertia

    727 Column Shift linkage installation tips?

    It'd be a tremendous help to have pix of what you are trying to install where. Pix of pieces you have etc. Tia.
  7. Inertia

    Good friend Died yesterday

    Very sorry for your loss .
  8. Inertia

    Solution to my leaking water pump weep hole?

    I believe the weep hole is there to protect the front shaft bearing being contaminated with coolant that has leaked past the seal, and now has the rear bearing awash.
  9. Inertia

    Motor won’t stay running

    Have you timed it yet,? if not, - pull a buncha timing into it, lots, pull the vacuum advance toward front of car a 1/2 inch or more, then start it. You can't hurt an engine starting it with too much advance cuz the starter will "balk" and refuse to crank if too too much. Once started, make...
  10. Inertia

    5.9 lifter ticking tapping noise SOLVED!

    Hope you rolled the pushrod on a flat surface. Bent pushrod may show similar marks . Cheers
  11. Inertia

    Sealing up valve covers

    lol - I prefer the black, lol
  12. Inertia

    Sealing up valve covers

    Im a big proponent of " let the gasket do it's job " I often assemble oil pans (on stand) with only 4 pea sized dabs of, now "Right Stuff" where the gaskets meet. (All regular RTV went in the garbage) Same with intake, no slather of goop, just 4 pea dabs where gskts meet. I do use 3M...
  13. Inertia

    Big Issue on harnesses from Classic Industries

    I've seen this post from you for over a decade. I can't explain the issues you had but here's a link to nothing but praise for Evans, perhaps the person making your piece was sick/ill that week. I have used several Evans pieces, and found them to be excellent, they responded quickly and supplied...
  14. Inertia

    Big Issue on harnesses from Classic Industries

    Family run, mopars only, - can custom make as nec, Parts, plugs, info, etc Good luck http://www.evanswiring.com/
  15. Inertia

    circle track rear gear ratio info needed

    Keep in mind you will get quicker, so get the gear that allows for that. I often never changed anything on the engine, but tuning the chassis and familiarity will make it quicker, a lot quicker . Drivers get better too, lol. I remember the first time we hit the chip, I damn near did back-flips...
  16. Inertia

    So... What did I buy?

    Front and rear throws are bored thru on 340 cranks.
  17. Inertia

    New Kevko Pan with Crank Scraper

    I know when I make a crank scraper, it doesn't look at all like that.
  18. Inertia

    THREAD SIZE NEEDED

    We used to grind down the shoulder/stop for the rear "washer", run the dye all the way past the missing stop, add another nut, the the rear-most washer, viola, adjustable strut-rod .
  19. Inertia

    PS box shaft size for pitman arm

    Not sure if this helps Just out of the box housing Small sector 1.11 Lg sector 1.22 https://www.bigblockdart.com/threads/steering-box-info.45860/ Cheers
  20. Inertia

    Motor won’t stay running

    Base gskt mismatch, vacuum leak, plug all vacuum fittings on carb, particularly PCV hose fitting .
  21. Inertia

    1 birth - 1 death. - Parents shouldn't outlive their children.

    Last Saturday, one of my sons and wife blessed us with a beautiful granddaughter. One floor up, - my other son was fighting cancer, - we lost him today . Parents shouldn't outlive their children .
  22. Inertia

    Headlight bucket adjusters

    They're in a bubble pack on the "HELP" parts tree/wall at my parts store.
  23. Inertia

    Multi voltage, adjustable soft to brilliant LED shoplites

    That was my problem, only fm I had was in a vehicle. lol
  24. Inertia

    Shipping from Dr. Diff in USA?

    Dr.Diff is golden . If you're close to the border, or not, check the location of the closest Kinek package handling. You can have pkgs sent to them just across border in US, have a buncha pkgs or 1, pay a small fee for each pkg, then bring it back across the border duty free if your outta the...
  25. Inertia

    Stock Market

    Not necessarily . This is the time to harvest tax loss before the end of the year. This is not uncommon. Fund managers, everyone who had a stock that lost money, not in a tax free account can claim against their "capital gains" to reduce their income tax bill. Every type of fund manager...
  26. Inertia

    putting a ford 5.0 in a 72 Dart

    Agree .
  27. Inertia

    putting a ford 5.0 in a 72 Dart

    I've been by-passing this thread for a while, but chuckle everytime I see it, reminded of the time a customer at my business, while walking behind my Dart, asked how he could get his Fex body to sound like my Dart. I told him he couldn't afford it, he asked why . I said " cuz I'd have to put...
  28. Inertia

    How to remove pin that hold the feet inside the steering coupler

    Right behind you, the vice, put a deep socket over one end of pin, squeeze the other side with the vice, pin will move into area of socket. Basically "press" it out . Once it moves, it'll likely move easier, might need something to push pin thru the shaft.
  29. Inertia

    Copper Header flange gaskets

    Draw File the flanges true flat, then Mr Gaskets forever. Works for me, never had need of expensive copper gskts or Remflex. Do it once . Good luck
  30. Inertia

    Multi voltage, adjustable soft to brilliant LED shoplites

    Wow, I can see into corners I didn't even know I had ! Got all but one lights done, so very, very bright. I can't believe I worked in there all these years, just wow. I have all but 3 turned up to 1 click shy of full, it's wonderful. I left 3 at 3 clicks down from full, and they are definitely...
Back
Top