Search results for query: *

These are local on facebook, not mine. Says they are PN/ 91582, for Prestolite distributors. If anyone wants them Ill can try to buy and ship. I know some love these...

Interesting story on the $4 'Hoover spacer' that realized 180+ HP out of a 'stock' slant. They mention our own Doug Dutra clicking off a sub 12 run. Make a 2" spacer and let us know your results!

Printed circuit board with voltage regulator. No broken pins, all traces, pads and pins ohm good. $25 shipped in USA. Up on Ebay Jan 1

All 3 gauges from a working Barracuda dash. $20 each or all 3 for $50 includes the pod. Guaranteed to work. A little dirty but ill let buyer clean them as the matte paint is very delicate. Orange needs a touch up on needles. Plus cheap shipping from So Cal or pick up free. Dash was cracked so...

tire plug gun.......see video in next. Someone posted he used one back in the 60s...this tech that old? not sure where the black penetrator ends up?

Kenda 16" tire on my minivan. Thing still has the nubs on the side and ~90% tread, probably less than 5000 miles on it but Im not the original purchaser, on vehicle when I bought it used. Its obviously a defect in the sidewall as there is no indication of any abrasion there or puncture. We...

trying to envision making a manual advance retard box out of an old dial back timing light. What electronic circuit does it use to delay the spark impulse to fire the xenon tube? All the delay circuits I look up are seconds, not milliseconds.......at 4000 RPM = 0.000138 seconds per degree! I...

for you Fakebook challenged viewers....CHRYSLER COMPATIBLE>408 ci - BluePrint Engines

If yours is in the garage or the kitchen.....mine wasn't draining the last 1" of water so I thought the discharge pump was shot. Stuck a fork in the interlock mechanism so I could see what it was doing. Filled fine, pressure pump worked, just a hum on the drain cycle. Pulled the discharge hose...

build it, dont buy it.......

So whats the test procedure to determine if these are leaking? I got one that has 3 nipples 12,3,6 o'clock. Im sure the 3:00 is the ported vacuum sense line as it holds a vacuum regardless when pulled on. The 12 and the 6 are both open to each other regardless of the vacuum level on the sense...

Basket case , not.mine....$200 in Riverside , Ca 1966 Plymouth Valiant

Not a slant six but a slant 4! Son ran his '98 Camry w/247K 2.2 low on oil (mystery leak, possibly front seal) and created a huge mess for his mechanic....ME! So I told him start looking for another car but in the meantime ill put new rod bearings in it and hope it holds together until he can...

In need of a thermovalve or ported vacuum switch, whatever Ma called it. Its usually on the intake or even the radiator of a 70s Mopar or anything else. 3/4 hex NPT with 2 ports, orientation is not important. It opens after 165F or some random engine warm temp to activate EGR or Evap or even...

Not really classic Mopar related unless you took the dive into EFI but Im flummuxed on my 2012 Chrysler T&C O2 sensor live data. I had a B2S2 (front post cat downstream sensor) heater circuit fail and a few other 02 related faults so I replace the one B2S2, then got the same results so I thought...

My.Mazda has mechanical EGR as most cars did in the early 80s. Simple: EGR is run off the ported vacuum. You crack the throttle, the ported vacuum would start to develop and the EGR would start to open gradually with increased engine speed. Some were run through a thermovalve so they would not...

HP04 oscillating fan with heater function and air filters. Its the weird Edsel grill looking fans for home use. If you can find one with no power , smell the bottom plate where the power cord goes in for burn odor. If you can smell burned plastic or rubber, the cord where it bends for the...

Would work on larger ones, novel idea! Span one wrench over side of nipple and then hook it with another and pull across the part. Nipple may slightly crush and break free.

Made a centering puck for the bottom (3D printed the OD of the raised centering boss of the hub) and a bullseye pad for the top that sets into the recess for the center cap. Bottom has a 3/8 drilled hole centered for a screw in golf cleat, wrap with pipe tape to get a snug fit. I sharpened the...

Dawn Wells...or Raquel Welch! It just wouldn't be the same if Raquel got the gig......

Friend found a hoard of knives pre estate sale from a deceased relative. They said take the whole lot and it was about 500 various China replica swords, machetes, multi-tools, combat knives....90% Chinese made trinkets. I saved these 3 original looking bayonettes from a $100 valued pawn shop...

PPG Ditzler paint codes 55-65 Chrysler Take it up 500% (CRTL +++++++++) http://www.jholst.net/paint-codes/paint-code.pdf

Whats procedure? I'm thinking pull cooler line into bucket and run another line back to trans and gravity feed it new fluid in via funnel at about the same rate? In neutral so it pumps? Flush until it runs red or out of fresh ATF? Cycle the selector a few times to clear the passages? Dumb they...

Not old Mopar related but may cross over.....2008 Mazda 3, no first gear, says shift solenoid stuck. Easy fix? just a new solenoid or are these usually TCM related? 192K miles. Solenoids are right under the trans pan, looks like a 30 minute job. No codes, this is for sale and Im just researching it.

Has anyone ever heard of this being used successfully and how is it not mainstream on cars today if it is so 'good'? A 5.9 Diesel (?) reported like 15% increase in torque and HP while decreasing NOx and CO by like 66% just by switching to a dimpled piston. Im going to be putting brand new flat...

Got one and of course you take it apart before you install it right? Redline (only importer of Weber carbs in USA) says set the float to: 18mm from top of float off the gasket with the needles spring ball barely touching. Then Pegasus racing say "...Weber recommends setting the height of a...

Saw this from Chrysler Engineer Dave Zelkowski, had this to say about aftermarket ignition systems- "The ONLY thing they will do for you is lighten your wallet. If there is nothing wrong with the stock ignition components it won't help. If you have some old tired components then it could be a...

https://img.alicdn.com/imgextra/i3/6000000005875/O1CN01HmTor01tGnSAPe75B_!!6000000005875-0-tbvideo.jpg phooey, the video shows him cranking this handle and the cutter milling the seat.

Dyson HP04 Hot + Cool filter fan. the ones that have a big hoop on top with no blades. For $400 this doesn't move alot of air but it does heat, and filter the air through 4 filters, 2 HEPA and 2 charcoal. My neighbor gave it to me instead of throwing it away as the motor was making a bad rattle...

Didn't even know these existed.... .....Replacement Off-Set Wheel Adapter Stud, for 6533 Adapters