Search results for query: *

Sorting out pulleys and need help with this big block pulley. Bolt pattern is symmetrical so after 72, iirc. It's heavy, and appears to have rubber in the back. What is this from?

Title says it all.

I recently swapped out my A833 4 speed for an A833 OD. All in an effort to actually use our car, as a car, and go on long distance trips, uncluding Power Tour 2025, for us a 2,500 mile round-trip. The idea was to swap my original A833 back in when I got home - nope! I drive it everywhere now...

My friend, who started a Mopar junkyard in '68, has 2 of these V3 Sunroof cars. They are rotted and buried, I never got a single picture of one, probably because they're unrecognizable, but they always intrigued me. Curious, does anyone here actually own one? Grabbed a few internet pics for...

2 sets. One from each set in each picture. At least that's how I bought them 100 years ago. I think I know what they came off, but what say the experts?

Multiple threads on adding 3 point belts to 68s. Able to locate only a few on 67, many without pics or measurements. 67 is the oddball with no shoulder belt mounting point, aka bump out (and some early 68s). 1st pic is of a friend's 67 fb, he welded in a seat belt mount. 2nd pic is a 68, I...

Very nice condition. I believe these were a JC Penny deal or the like. $125 shipped to the lower 48.

Used Old School Cragar bbp Center Caps, no backing plates, screws, or R. $225 shipped to the lower 48. I don't know why they have different colors, I bought/sold many to get the perfect set. These are the runner up. They have minor pits, scratches, etc. Pics of the worst spot on each. They...

$200 shipped to the lower 48. Manual choke. Clean. Been sitting without gas, so maybe go through it, or slap it on, your choice. I bought it from a fbbo member who used it for a short time, I ran it on my 383 for a shorter time to break it in.

$175 shipped to the lower 48. Looks like crossover had issues, a repair, one of the runners nearby has a nick. Looking at it from the coil bracket side, the bottom inside left carb thread looks weak. I could be missing something, it's used.

1984 Dodge Ram, it has a 2wd cab, big lift, and a W250 chassis, from what I can determine. Are both rear and front Dana 60s? Dana 70s? The rear has a cover with a rubber plug, and I want to order one with a threaded plug that is higher, seems low to me. I checked Denny's, only one in stock is...

Looking for direct bolt small bolt pattern spacers, steel or billet, 3/8 thick. New ones are available, just checking here first.

Looking at spacers for the front of my 67 Barracuda with KH disc brakes. 4.5 bolt pattern and up spacers are easy to find, but I did find these for 5x4, although listed for a VW: 5x4.00 Flat Wheel Spacers Stupid question: How do spacers work, do they require longer wheel studs and the same lug...

Clear Plastic with Rubber Bands on Rear Seatbelts It's official, rear seat belts were shipped with small clear plastic bags over them secured with rubber bands. A friend's survivor car had them, wasn't sure if that was a factory thing or owner personal preference. Saw a 10k mile survivor...

Ok, I'm a 67 Barracuda geek, and a little overboard on the history details, so hang on if you're interested. In 2008, within a few weeks, two people who never met, me being one, each bought a 67 Barracuda a few miles (200) from where they were originally sold new and brought them back east, to...

67 Barracuda. Looking for front driver/passenger floor sections from torsion bar cross member to firewall. Also rear bottom sections pictured, with the round drains. Would also consider lower corners of fastback window. If someone has cut up car let me know. Not looking for new. I'll buy...

Searched, found same issue, but solutions don't seam to apply. Upgraded to bbp axles, housing completely cleaned, center section sealed up with new gasket, vent cleaned up inside and out and resealed, used a little green tube gear oil rtv on both. Rear was filled on a lift just below the fill...

Thought this was cool.

Other than the obvious differences in the area under the seats, what's the difference between these 2 floors? Top one looks exactly like my 67 Barracuda floor, but bottom one appears to extend farther in the back.

:) I walked around everyday, took many many pics.

What's the best option here for me? I bought the car in 2008, covered the holes with the stuff in the pics, there is sheet metal laid under the front sections, yes, I know. I have since replaced every floor panel in a 62 Dart, with a welder. Full pan replacement seems too drastic in this case...

SBP, small bolt pattern. Custom made 15x7 steelies, 4.5 bs. They were powder coated a bronze color, then painted black. No rust. Cooper 255/60s, used, white letters in. $600 local pick-up. NY 12302. I went bbp, were on the back of my 67 Barracuda. FYI, wheels do not fit the front, hit UCA.

I've read through many threads, no luck. 67 Barracuda, original sbp KH disc, QA1 UCA/LCA/Struts, Hotchkis swaybar. For years ran Cragars, 14x6 3.75 bs, 215/70/14. Switched to steelies, 15x6 3.75 bs 215/65/15. When I switched to 15x6 I figured what tires would be same size and they are near...

Pair of green sun visors. These were in the trunk of a car I bought, they are identical to the ones in my 67 a-body, may fit other models. Original old visors so not perfect, need a good cleaning I imagine, but not brittle garbage, no rips, tears, or cracks, and not coming apart at the seams...

Looking for the decal/sticker in the pic below. It has an engine turned kind of look to it. Pic is of my car and it has been on the rear window for a long time. I do not know the maker, but I do recall seeing them all over for all makes when I was a tiny human.

$9,500 located in upstate NY 12302. NY transferable registration. Comes with roller wheels/tires in first pic on trailer, white set is on another car now. Original slant 6, 3 on the tree, 8 3/4 open rear. Manual steering, manual drum brakes, dual master cylinder. Original interior, radio...

I know enough, I think, to know a 1954 331 Hemi is a good piece. The bellhousing is not cast into the block, although my understanding is the ones with the cast in bellhousing, with a readily available adapter, can accept a Muncie 4 speed. It is stamped C542–8-9016, and apparently from a New...

Looking to put a fitted cloth cover of some kind over my vinyl recovered bench seat. Just to use for long drives, for either hot or cold weather. Has anyone found/used such a cover? I know my local parts store has generic (gigantic) bench seat covers, just too big and bulky.

Checking to see if anyone has 2 used small bolt pattern 15" chrome reverse wheels / rims they're not using. Idealy, 15x8, possibly 15x7. Yes, I know. I already have front runners and 14x6 chrome reverse for the rear, I'll run them if needed. Not looking for Centerlines.