Search results for query: *

Picked up at an estate sale. $150 for all. Local pick up only unless you want to arrange shipping. These things are heavy! Pics available upon request. All are used but in good shape. #6227-1 and 6227-2 Spring Compressor and Alignment Shaft #C-3863 Front Clutch Assembly Remover and...

Got these at an estate auction last weekend, guy had a transmission shop and must have specialized in Chrysler transaxles. Most have Pentastar on them, some do not. All are loose without packaging but in good shape as far as I can tell. I don't do paypal and that other nonsense, so if you...

I upgraded my ignition to HEI over the weekend, and now my tach jumps through a range of 800-1000 RPM. Tach is an old Sunpro, connected to the negative post on the new coil as it was with the electronic ignition I replaced. Tach was rock steady with old ignition. What other information does...

I'm OK with mechanical stuff, but electrical is just to the left of witchcraft if you ask me. So, how do I go about figuring out how large an alternator I need, based on the accessories I have now and what I may do in the future. I have a relatively new 60 amp alternator and have added no...

I've got some leftovers I'm getting ready to sell, fenders, springs and so on, and when I check the usual suspects for shipping rates I'm aghast. Just to ship the fender via UPS or Fedex ground it'll be around $200 because of the dimensions. Anyone have any tips on shipping this kind of stuff...

Looking for a GPS speedo to use in my Dakota, not really looking for in dash gauge type. Want cheap but reliable/accurate, with odometer if possible. Don't care if it plugs into cig lighter or direct wire. Any suggestions?

A while back I bought a 99 Ranger with the 4L V6, with about 135,000 miles on it. Nothing much to look at, but drove well and everything else looked OK. Met the guy selling it so it was already warmed up. It sat for about a month until I put it into service as my daily driver, and lo and...

The last few times I've taken the Dart out, it has wanted to die when taking a 90 degree right turn, like into the gas station, my driveway, etc.. The engine will quit about 3/4 into the right turn, and then takes a few cranks before it will start up again, like the carb is empty. Any other...

Been fighting this intermittent problem all summer, and have had just about enough. Early this year my 69 BB Dart wouldn't start, no gas to the carb. I was pretty sure there was gas in the tank but I put a couple of gallons in anyway. A little down the carb and it fired right up. Ran fine...

Anybody know the temp at which the factory gauge was calibrated to read "H"? Gauge is from a 69 smallblock car if it matters.

Anyone know what the correct length for a fuel pump pushrod in a 383, and what the wear limit is/may be? Having a fuel delivery problem and I've exhausted just about everything else.

Need one LCA pivot shaft for use with rubber bushings, for '69 Dart. Will take pair if necessary. Shoot me a price with shipping to 55441.

I took the instrument cluster out of my 69 Dart, repaired the broken pins on the printed boards, and reinstalled. Now I have no brake lights or turn signals. The tail lights work when the headlights are on and the emergency flashers work....on the rear only. In fact, I have no front running...

I have a 69 Dart, and am looking for LCA's with the sway bar tabs. I have someone locally that will sell me an entire SB K-Frame with UCA, LCA, disc brakes & a sway bar from a 73 or 74 Valiant (he says). Will any of this fit on my '69, and is there anything specifically I should look for to...

I rebuilt my 727, including replacing the tailshaft bushing. I got a new yoke from Inland and while it fits and slides just fine on the output shaft, it sticks about an inch and a half into the tailshaft. I chamfered the edges of the bushing when I installed it. The yoke can be forced in, but...

I need a 187 or 699 oil pan to put the big block in my '69. Anyone got one? I have a 402 right now, does anybody know if this pan will interfere with the steering? I'm using the Schumaker conversion mounts if it makes a difference. ****Just got my hands on one, thanks for looking.****