Search results for query: *

So I dropped in my fresh 360 along with a rebuilt 904 and 8 3/4. My problem is that in idle or when I have it on jack stands it runs great. I can pull rpms and the throttle response in awesome. Now, when I pull it out onto the street I can't pull anything beyond 2500/3000 because it breaks...

I picked up a rebuilt 904 and installed a Cheetah forward manual valve body myself after I picked it up. Thought it was a pretty straight forward install. Well I got everything together and it slips in the forward gears but reverse works good. Like I mentioned,when I put it in any of the...

So I dropped a 360 into my Scamp, at the same time I installed a new idler arm and upper tie rod end. The idler arm hits the bottom of the header and the tie rod end is so close the rubber boot in melting. Any help would be much appreciated. The headers are Hooker Comp's. I will...

I bought a set of backing plates and drums. The drums measure 9" and the pads measure 2.5" wide. I need wheel cylinders for these and this is the only information I have no idea what they came off of so when I hit up the local Napa or O'reilly I'll probably leave empty handed. Can anyone...

So I picked up a rebuilt 904 and installed a forward manual valve body myself after I bought it. Seemed easy enough to install the valve body so I decided to do it myself. On my first trip out it slips in the forward gears and doesn't shift firmly into any of the gears either. It does...

Would a starter out of a 2002 Dakota work as a mini starter in my 360 LA? Thank you.

So I ordered up my ARP flex plate to crank bolts #240-2801. The bolts will not seat all the down, seems they are 1/4" too long. Any ideas on what could be wrong?

I installed the balancer on my 360 and when turning it over by hand I noticed the damper kind of pulls away at one point when watching the damper come around past the timing marks on the timing chain cover. Moves 1/16 of an inch or so. Is this normal? Thank you.

I picked up a 360 short block and as I go to install the harmonic balancer with a piece of threaded rod to draw the balancer in, the threads stripped out. Not sure if it was like this or something I did. Anyhow, besides pulling the crank is there another way to repair this? The engine is...

What size bolts do I need for mounting flex plate to the crank on my 360? Thank you.

Is there a way to bench test a mechanical fuel pump?

I installed a new cam and timing chain set in my 360. When lining up the dots on the cam gear and crank gear should the #1 piston be at TDC? I haven't done this years and need a refresher. Thank you.

I have a new MP 508/292 cam Part number P4120233. It has been installed but never ran. This is the cam only. No lifters. Located in Inver Grove Heights MN $90.00 + shipping from 55076

Is there a cam out there that is equivalent to the 508? I've got one in a 360 short block that Im putting together and thinking of going with a different brand with the same specs. Thanks.

In my 74 Scamp I swapped out the /6 and 7 1/4 for a 360 and 8 3/4. Any idea and what my drive shaft length should be now from cap to cap? Thank you.

I'm looking for 73 and up /6 to 360 motor mounts to use with a /6 K frame. Thanks!

I have a set of 14x4.5 wheels. What would be a good size tire to mount on these wheels? They're for the fronts on my 74 Scamp. I'd like to go as tall and skinny as possible without bulging on the side wall of the tire. Thank you.

What's the skinniest tire I can fit on a 14x4.5 steelie for my 74 Scamp? Thank you.

Friend of mine is going to Destin Florida. Are there any Drag Strips close by? Thanks.

What's the most tire I can fit in the wheel well of my 74 Scamp with rubbing with stock wheels? I believe they are 14x4.5. Not sure on the back spacing? Thanks.

I'm looking a pair of 5x4 to 5x4.5 wheel adapters. PM with price. Thanks.

What size U bolts do I need for an A body 8 3/4? Thank you.

It's been years since I've put a 8 3/4 togther. I cannot remember does the spring side of the inner seal face in or out? Thznks.

Will the backing plates / drums from a '86 5th Ave bolt up to a BBP 8 3/4?

I need a set of crank offset keys for my 360la. Where can I find these? They usually don't come with timing chain and gears set do they? Thanks.

Do all double roller timing chain / gear kits have degree notches?

Looking for a 9.5 or 10" convertor for a sb 904. Like to stall around 3000 to 3500 or so. PM here.

Looking for 8 3/4 backing plates loaded with brake hardware and drums. Must be in usable condition. PM here. Found locally.

How do I determine what size backing plate I have? I bought a 8 3/4 housing and it came with backing plates. I need to install all the hardware now so I need to figure out what size I have. Thanks.

Looking at a used 9.5 Dynamic convertor for my 360/904. Anyone use Dynamic? Thanks.