Search results for query: *

Are the 68 coupe/convertible rear seat backs the same in the coupe and convertible?

A couple years ago I purchased a repo center console and it was junk. Are these restoreable?

Anyone restore their vent windows, and if so do they need to come off for professional refinishing, or can they be cleaned up in place? If I can resto them without removal, what's the best course of action?

Anyone remove the vent windows from a 68? If so, any advice for easy removal, is it a pia?

Anyone know where I can buy these?

After years, I am now serious about changing out my 3.23 rear for a 3.73 or 3.91. I have a gen III 5.7 hemi (360 HP @ 5400 rpm/360 ft-lbs of torque @ 4200 rpm) and five speed with 3.27, 1.98, 1.34, 1, and .68 gear ratios. My rear tires are 26.7 inches tall. I drive the car on the street and...

Anyone purchase a drop-in third member from justdifferentials.com? They quoted me $1,164 (shipped) for a 741 unit with a sure grip and 3:73s.

I did a search last night for Dart heater controls and didn't come up with much. My top control (heat/defrost) doesn't work right. I took the dash apart and it looks like it's seen better days. Are they easily rebuildable, or can they be purchased repo'd?

So my fuel and temperature gauges only work properly when the lights are on, regardless whether it's the parking or headlights but after awhile, both gauges go all the way to the max readings. When the lights aren't on, neither gauge reads accurately. Another weird thing is that when the lights...

My speedo flutters and makes a ticking sound. I was thinking about disconnecting the cable from the back and shooting in some liquid graphite but I'm worried the black spray from the graphite might come through the backside and stain the face of my speedometer. Any advice would be greatly...

I need two taillight bezel screws, should I be able to find these at a well stocked hardware store?

Want to replace my convertible top snaps. Someone had mentioned trying my local crafts store but I tried to no avail. I need 27 of them, anyone know where I can get a set (with the screws in them)?

Can someone pls post a pic of the location where the trunk rubber bumber goes and what it looks like? There are two potential locations, one close to the edge that is round (i think this is a weep hole for water to escape) and another that is rectangular. I've attached a pic but for some reason...

So I just got my rubber bumper kit, which included the door bumpers. The bumpers included in the kit are longer and much more meaty than the ones in my '68 vert. I bought them on ebay and the seller said I can cut the length down so they'll fit in the hole where they go and they should be fine...

'68 vert, need the rubber bumpers that go on the bottom of the trunk lid (near the bumper), where can I purchase them?

Just got the body done on my '68 vert. Noticed that my trunk lid has a little play; I can push down just a little bit when the trunk latch is engaged. I adjusted the latch last night but when I was able to get the trunk lid to close securely, it was down below the quarters just enough so it was...

Where would i get new carpet to around the bottom of my stock '68 center console?

Got new hood inserts for my GTS from P&G. There are five plastic posts on each insert that affix to the hood using thread cutting nuts. The problem is the front post of each insert doesn't stick through the hood enough to get the thread cutting nut to start. I'm thinking of substituting a...

I'm thinking about buying a car cover on ebay. The manufacturer is Auto Armour and it is a 4 layer type. The cover will only be used indoors in a newly built, well insulated garage. I've attached the link; anyone own one or have thoughts...

In process of restoring my '68 and I need new convertible boot snaps. There are 24 of them that screw to the molding around the well. Where is the best place to purchase them?

I'm looking for the retainer clip that holds the driver's side window glass into the track; anyone know where I can buy one?

I ordered new door weatherstripping for my '68 'vert from YearOne. The part number is FR7456. It doesn't fit perfectly but I think I can get it to fit. The description says it's a 67-72 A body door seal for a 2 door hardtop but doesn't specify convertible. I called yearone and the guy I spoke...

I need about 13 clips that go on the rear finish panel of my '68 GTS, any idea where I can buy them?

I'm having my trunk finish panel and grille professionally redone and the person doing the work wants to know if he should leave the nice argent color that resulted from anodizing or lightly paint each panel's accents in silver. He is matching it to pictures of GTS grilles/finish panels that I...

Must be in very good restorable or ready to go condition.

Please let me know what you have. I don't want any driver quality pieces though, as I just stripped the one I have and it's barely restorable. Want a nice restorable or ready to go piece. Thanks

Anyone have one for sale in either real nice restorable condition or ready to go? Thanks

I need new weatherstrip for my doors but none of the suppliers list it for a convertible so should I assume that the weatherstrip that fits the coupe is the same?

Convertible belt moldings for a '68.

Can anyone comment on Classic Industries' fit and finish on their repo headlight bezels and hood lip moldings for a '68 Dart?