Search results for query: *

crackle.com has some good old shows like tj hooker, starsky and hutch... free too

sorry, i forgot to say that these numbers were on the passenger side of the rail. And i believe they should be exact numbers to the vin on dash.

It's pretty easy to tell for sure if it's legit, there should be another vin number on the box rail just in front of the back tire. 78's were closer i believe to the bottom of the frame rail and the 79's were up a little higher.. Hope that helps.

x2 on the amonia stuff. I pulled some off a few cars and was left with tones of glue, the amonia window cleaner took it off real good.

No prob, i totally understand..

Hey Flyguy Welcome, were you from in SK? I'm from Weyburn, there are a few of us from SK. Weyburn puts on a decent car show every June, a few hot mopars but the one to go to is Southey, all mopar. Any chance you would sell the grill of that car? I have been looking for a sharktooth grill...

Thanks Kork I always like those slots too, but could never find them, now i've got 2 sets. One is all small bolt pattern though. I wasn't even sure they made big bolt pattern in those but a guy i know gave me an old set and the back ones were bbp. And i always figured 1970 was the year to...

Here are some of my baby's. The 09 R/T is a buddy of mines car..

When i make it, i just get the butcher to slice up a roast real thin, then i put it all in a container, put some soya sauce in, lots of garlic, and spices (what ever you like) cajun spice or some good hot pepper sauce. Brown sugar if you like the teryiaki way. I put some ginger ale in it...

Yes thanks, I ordered a new hood, fenders, lower valance and bumpers from them for my 72 demon, so i'm hoping there as good as everyone has said. Was a little bit of a pain for shiping since i live in canada (had to line up a broker) cause there were shiped by truck and not courior which...

Ya those always seem to look good on our Abodies..

Had this one for a long time now..

Hi all, Looking for a tunnel ram for 360 (408), let me know what ya got. Pics would be great. Would have to be shipped up to the great white north, if in the states. Thanks Jason

This is what was done to a 95 360 magnum i put into my duster. They figured it was pushing around 437hp.. With 391's in the rear, it was a blast to drive.. Block - 360 Magnum Machine Work - Bored .060, Torque Plate Honed, Align Bore, Square & Deck Block, Magnaflux, Balance...

Just one other thing about blueprint engines. The place i got mine through had ordered 2 at the same time and i ended up going back one time and they still had the non dressed version of mine, (these motors state that they are hot ran and dyno'ed), sooo i ask if i can see the specks on the...

I put one in my LIL Red, I got the fully dressed 408, couldn't get it to run right untill i got rid of their carb, wires and plugs. Seems to have some good torque and hp but i would never buy another one from them again just because with all the original probs i had their customer service was...

Hey Fstfish Just measured the blower. From front to back its measure's length 14.5", height is 7.5", Width is 11.25...

Well the guy i bought it from said thats what it was. I'm not really sure how to tell the 471/671/871's apart. Here is a pic though.. Let me know what you think. The old rad is gone and a aluminum becool one is in now..

Hey Guys I just picked up a 72 demon with a 340 and a 471 blower. First blower i have ever had so i'm a little on the paranoid side of it all right now. I have driven it a few times now and my temp gets up to 190 sometimes even 200 but then i get scared and pull over. Then i keep the...

Yes that is the only reason i am wanting to switch is so i actually have a bigger selection of rims, i have cragers and slots, but would like to go with center lines or weld wheels. I just replaced the master cylinder and am pretty happy with my brakes now so i didn't really want to have to...

Now thats what i'm talking about, thanks...

Thanks very much guys, i've changed a 100 motors and trans in my life but when it comes to front end stuff i get a little gun shy, i have visions of doing something wrong, and then crusing down the highway sometime and my front end goes out on me and i'm in big doodoo cause i'm going a little to...

Thanks guys, i did read about the mustang rotor, but in my neck of the woods i don't think i would ever find anyone that could do that for me. Is that all a guy would need is the big bolt control arms or is there anything else a guy would need?

Hey Guys, I have been searching for the easiest way to swap my small bolt pattern disk spindle out to a big bolt pattern disk spindle but have had no luck. There is plenty of info on going drum to disk but not small bolt to big bolt disk. Thanks Jason