Search results for query: *

great shape, 12k miles on a 13 charger and used for 1 season on my build. Psi1515 springs and Manley Titanium retainers installed. Extremely clean. $850 plus shipping.

Msd hemi 6 ignition box and harness. Good shape. Less than a year old. Harness isn’t chopped up or anything. This plugs right in to the modern hemi for use with a carb. 600 shipped.

out of sfi spec, good shape. 300 shipped

i have these items cross posted, so don't wait too long. I can ship everything. Edelbrock performer heads, Hughes valve covers, and Mancini roller rockers with arp hardware. Great shape, correct arp headstuds. Low miles $1600 complete, bolt on and go! Out of the box from edelbrock. Arp head...

Late 360 block, 3/4 fill 408ci Scat forged 4" crank. Hughes girdle/arp mains. Scat H beam rods. Cp pistons 11.0:1 compression. Cometic head gaskets. Edelbrock performer cylinder heads. Mancini 1.5 roller rockers Arp headstuds Hughes fabricated aluminum valve covers Super victor intake...

magnum based manifolds, 2.25 crossover, twin 38mm wastegates, borg warner s480 turbo, CSU 750 e85 carb and boost reference regulator. This kit will support over 1000hp of need be. It's a proven kit that have propelled my car at 3600lb to 9.30s in the 1/4 at over 146mph. I'm switching engine...

came off a running, really nice shape. Was going to use them on my early 5.7 to bump compression, but plans have changed. Can send more pics via email. 400 plus shipping. Please pm me.

fit 1960-76 a body. 20" front segment, 35" rear segment. Good shape, some paint overspray from some idiot painting the car. Should come off with some work. Everything works as it should, and moves freely. $600obo They are over 700 new, plus 100-200 shipping. Due to the weight and siZe...

318 heads off a 83 d150, new guides, comp 901 dual springs, valve job, and seals within 3000 miles of being removed. They've been on the shelf for a bit so they'd need cleaned up, otherwise they are ready to bolt on and roll. Have stock rockers, rocker shafts, pushrods, and assorted fasteners...

new strange 1350 cast yoke. Installed, but never had a driveshaft bolted to it. $93 plus shipping from jegs or summit, I'll take $80 shipped in the lower 48.

489 case caps, and adjusters, with oem 3.23 pinion installed, includes matching oem ring gear. has big yoke as well. no carrier. Add your sure grip and roll. 225 shipped in the lower 48.

489 case, oem 3.23 gears, with a 35 spline spool out of my turbo car. really nice shape. went dana and have no use for this or my extra 8.75 parts 400 plus shipping.

35 spine, used, in great shape. 100 shipped in the lower 48.

It's a long shot, but I have a 489 case, 3.23 factory geared, 35 spline spool center section out of my turbo car. Works fine very very slight wine on deceleration, but works fine. 400 plus shipping OBO.

CRT super pro 904 Billet steel drum. Red clutches Red lined bands Steel 4 pin planetary Deep aluminum pan Sfi small block flexplate 9.5" ptc converter All the good stuff Still in the car, can show functionally. Will remain in car, until purchaced. Trans is $2800 from CRT without...

489 case, 3.55 factory gears, cone style Sg. Very very nice shape. 700 plus shipping from 45420

360 block, 3/4 fill (never sees over 210 oil temp even after hour highway drives) 4" forged crank Scat h beams Hughes custom turbo cam Cp pistons Billet timing chain gearset Ati balancer Edelbrock heads Super Victor intake Cometic headgaskets Arp headstuds Electric water pump Hughes valve...

Complete 5.7 hemi from a wrecked 1500 the was smashed in the rear. Truck had just rolled 60k miles and ran great. Engine is complete with the harness. The only thing missing is the ecu. Easy going to swap it into an older mopar, but changed directions. It's located in Dayton Ohio 45420, and I...

I've got a used holley hp ecu, works good, does have 2 bad coil drivers due to cheap aftermarket coils used previously, so it cannot be used on gen 3, ls or coyote engines, but works fine with a distributor/ignition box setup. Retails for 1100 for just the ecu 650 shipped in the lower 48.

For magnum heads or w5 or w7 heads. Less then a year old. 100 shipped.

I've got a used set of hughes iron ram heads. 2.02 intake valve. Fresh valve job and just resurfaced. Heads have retainer to guide clearance opened up to accept .630 lift cams. Includes pushrods for use on la block. Also includes studs and guide plates to use sbc rockers. Has springs spec'd for...

I've got a used set of hughes iron ram heads. 2.02 intake valve. Fresh valve job and just resurfaced. Heads have retainer to guide clearance opened up to accept .630 lift cams. Includes pushrods for use on la block. Also includes studs and guide plates to use sbc rockers. Has springs spec'd for...

Used, works good, minor scratches. 275 plus shipping from 45420

-Csu e85 750, single needle and seat, less then a year old -Extreme velocity carb hat, standard height -Quick fuel boost refrence regulator -Magnafuel prostar 500 fuel pump, less then a year old All goes as a combo, will not separate. Came off a stong running combo. $1500...

2.02 valves, springs for a solid cam, new guides last season. Scorpion roller rockers, comp studs and guide plates. Off a running engine. Clean them up and get some power out of an old tired la or magnum motor. Also have indy single plane intake for another 300. 1300 without intake, 1600 for...

Stock 360 cast crank, stock 360 reconditioned rods, new cast pistons with new rings. Add bearings and throw it in a block. 300 plus shipping from 45420 Email [Please use the PM feature to exchange Emails]

Have a crt super pro transbrske transmission, bought it September 2014, works great. Have all recipets and paperwork. Will ship on buyers dime. 1900 plus shipping from dayton ohio...

I've owned this car for 7 years in july. It's by no means pretty, but it was build for one reason, to go fast. It could easily be turned into a sleeper with some steel wheels and dog dish caps. The body is straight. The bottoms of the doors need attention, as does the rear quarters. Kit does...

This unit was made for a 4"ish arm small block. It's a 9.5" converter. Was just gone through at the end of last year. This isn't a off the shelf converter you can go buy at jegs. 3 passes and minimal street time on it from the last refresh. Works great have no use for it. Paid over 1000 plus...

742 case, 4.56 richmond gears,factory sure grip. Works great. 550 picked up in Dayton oh.