Search results for query: *

Hey FABO so this past weekend I went to install a transmission mount on my 66 barracuda and while doing so by dropping the tranny a bit I managed to mess up my throttle linkage a bit. Its now very hard to accelerate but I looked and the linkage now goes into the firewall at an angle and the...

hey guys I am running a 360 in my 66 barracuda and am trying to find out a good timing setup to run. The engine has a 218/224 cam, 670 cfm holley carb, RPM Air Gap intake and MSD 6AL box, with the stock distributor. Right now if my memory is correct my timing was right around 8 degrees. But...

Ok I feel like an idiot asking this question but I recently got a prothane trans mount to use in my 66 barracuda but the only mount that I can find is the crossmember. Is there another mount that I'm not seeing. Transmission is a 727 connected to a 360

I'm looking for a barracuda fish emblem like the one on the fender of a 67-68 just need one. Condition doesn't matter either. If you have one laying around please let me know.

What kind of fans are good for extra cooling power for my 360 what's a good setup for it Thanks

Looking at getting better compression out of my 360 it's in a 66 barracuda so far I have the rpm gap intake 750 carb but swapping it down to a 650 and a 218/224 cam so far have stick heads but looking to get around 400 horses out of this engine what's a good head to go with

Hey guys in a bit of a debate on a facebook group on what a muscle car really is here is the question that was asked and please give me what you guys think is the real answer Is the dodge neon especialy the rt and srt a musle car or tuner normaly its obvious a civic or beamer a tuner a...

The Story of my 1966 Plymouth Barracuda Hey FABO be here for a while but never shared the story of my barracuda and how i got it and where it has came and how it is now. It started all when i was 10 years old when i picked up a paper route in my neighbor hood i did these for 2 and a half...

Hey so i just replaced my battery lasy summer it was originally connected to my slant 6 but then i ugraded and swapped a 360 into my 66 cuda after i drive it for a bit and park and turn off the car it makes a little bit of a bubbling sound. should i be concerned

Hey guys so i just swapped a 360 into my 66 cuda it had a slant 6 in it before. I have ecently gotten a new alternaor and i have gone through 3 voltage regulators. What is happening is that as i am driving my ammeter goes all the way to charge and the wire going to that gauge gets really hot and...

Hey guys so i just swapped a la 360 into my cuda and was wondering if anyone could give a rough estimate on horsepower that i would be pushing. the mods are Holley 750 cfm carb edlebrock highrise rpm intake manifold 218/224 comp cam msd blaster 2 coil and ignition box also then what gas...

im looking for 2 barracuda fender emblems off a 66 the ones that look like this dont need in perfect shape please pm me if you have these and are not asking alot Kris

Hey guys so about a month ago i swapped a 360 into my 66 cuda and pulled out the salnt 6. Now here is the issue whenever i rev my engine or even drive it for a bit i loose my signal lights and the alternator gauge goes past the c on the gauge. i have swapped a new alternator and it is still...

Hey FABO im selling a set of gauges that were installed in a 66 cuda I bought but i am sticking with the original look they are Autometer Ultra lights I have the MPH, RPM, Oil Pressure, Fuel, Volt, Water Temp. These are in BRAND NEW shape installed for less than a month then i bought the car...

hey FABO i have a 66 barracuda and was looking for louvers for the back window were they even made for my car or would anyone know wa company that could make em Thanks

Hey FABO so have a second 1966 barracuda in my backyard right now and i am going to be selling parts for it if there is any part you need just ask i have a lot Kris

Hey guys so I need 2 bf goodrich ta radials p205/70r14 93s does anyone know where I could find a pair

Looking to get a six pack hood scoop for my 66 barracuda any year will work as i am getting it molded into the hood of my car thanks. PS i live in canada but i am willing to pay the extra shipping