Search results for query: *

I have some 5.7 hemi parts for sale. It is perfect for mocking up the motor. I have a bare 5.7 block that can be built. A set of early 5.7 heads. I also have a truck and a car front timing cover and alternator for each set up. I have tti biscuit mounts for an a-body. I also have a plastic 5.7...

I have a A-body 4 speed I am putting together. It has all new syncrhos and the gears were matched to them by brewers. It will come with a billet shifter plate and a fiberglass tunnel. I would Like to get 800 for everything. Its located in Old Saybrook CT Thanks Bill

The owners of Afxer.com, Steve Mangante and Englishtown are teaming up to try and get as many A/FX cars together as possible. Any A/FX car can join us from tube chassis cars to all steel cars. The event will coincide with the annual Mopars at E-town on Saturday August 24, 2013. There will be a...

I have a few hemi parts for sale. 5.7 block that needs a little clean up Im looking for 400 for it. It does not include internals. I have a truck front timing cover w/ a water pump and alternator I would like 100 plus shipping for it. I also have a truck intake and throttle body I...

I have a radiator out of a 1972 Dodge Dart with a 318 and A/C. It did not leak when I took it out of the Car. It is original to the car but I am Swapping in a 6.1 Hemi so I no longer need it. I would like to get 50 dollars for it. It is located in Old Saybrook, CT. I have pictures upon request...

Good running 318 for sale. It was pulled out of a 1972 dodge dart about 4 months ago. The motor has good compression in all eight cylinders. It did not smoke when it ran. The cam has been upgraded to a Lunati Voodoo cam. The cam was broken in properly following lunati’s directions. It also...

Aluminum Small Block Bell housing For Sale. Aluminum bell housing for 69-71 small block to a833 for sale. I have misc clutch linkage to go with it. I would like to get $120 for the bell housing and clutch linkage. Parts are located in Old Saybrook, CT

4.30 sure-grip 489 center section available for sale. It was built by Randy J out of Connecticut. It has very low mileage on it. It has a crush collar delete installed on it. It also has a big u-joint setup. It is built for a Street/Strip application. I would like to get $600 for it. It is...

Aluminum Small Block Bell housing For Sale. Aluminum bell housing for 69-71 small block to a833 for sale. I have misc clutch linkage to go with it. I also have a z bar that needs some repair. I would like to get $120 for the bell housing, zbar and clutch linkage. Parts are located in Old...

I am going to be using a standalone ecm in my car and would like to use a 545rfe. What options do I have to control the transmission? Thanks Bill

I have a truck front timing cover with waterpump and alt I would like to sell for $125.00 plus shipping obo. I also have a truck intake with injectors fuel rails and throttle body for sale for 125.00 as well. I am selling these because I am putting a car front cover on my dart with a...

I may be interested in selling my four speed setup. It includes a freshly rebuilt A833 with new synchros and bearings. I also have a hurst super street shifter with rods. Also an aluminum bell housing and an assortment of clutch linkage and a fiberglass floor tunnel. I would like to get 1100 for...

I have a pair of magnum manifolds that are in good condition for sale. I am asking $100 plus shipping. Thanks Bill

I have a truck 5.7 hemi Intake manifold complete with Throttle body, fuel rails, and injectors for 125.00 Thanks Bill

I have a Truck front timing cover for a 5.7 hemi. It comes with a water pump and alternator I would like to get 125 for all of it plus shipping. Thanks Bill

I have a 1972 318 out of a dodge dart. Motor runs very well when pulled from the car. It can be had as a long block for $200. It has an upgraded cam shaft and looks to have been rebuilt freshly. Thanks Bill

What sort of modifications did you guys do to make the steering column clear the left side cylinder head?

I have a 1972 318 that was pulled out of mY dart to make room for a 5.7 hemi. It ran well when I pulled it out. It is complete pan to carb. I am looking to get $300 for it. Thanks Bill

I have a 489 case third member with 4.30 gears. It has very low mileage on it and I would like to get $500 for it. It has a crush collar eliminator kit. I would prefer not to ship it. Thanks Bill

I am looking for a 1973 to 76 a-body v8 spool mount k-frame. I have a v8 biscuit mount frame if interested in a swap. I would prefer the part be located in Ct. Thanks Bill

I have a 340 block that is standard bore. It has some rust in one cylinder so it may need a sleeve. It comes with a set of j heads that need built. I would like to get 300 obo for the heads and block. It is located in Old Saybrook CT Thanks Bill

I have a 1970 340 intake manifold. It has a brake around the choke housing but it does not affect the way function of the intake. I would like to get 100 dollars plus shipping for it. It is located in Old Saybrook CT Thanks, Bill

I am having trouble getting my magnum manifolds to fit on the drivers side of my 72 dart. I would like to see any turbo set ups using magnum manifolds. Thanks Bill

I am looking for a trunk gutter for a 1970 dart.

I have a 318 out of a 1972 dodge dart. It has a forged crank. I recently put a Lunati voodoo camshaft in it. When I did this the motor looked very clean inside as if it had benn just rebuilt. It also has a 1970 340 cast iron intake and a edelbrock 600 cfm carb. I am asking 350 for the engine. It...

I have a 1971 date coded 340 block for sale. It has the factory forged crank with it. The mains are still on the block. It does have some rust on one of the cylinder walls so it may need a sleeve. I am asking 350.00 for it. I am located in Westbrook Ct. Thanks Bill

Were is a good place to get a car timing cover from? thanks Bill

I have a pair of magnum manifolds off a 1992 dodge truck. They are in great shape. I would like 120 plus shipping. They are located in Westbrook CT Thanks Bill

I have a 318 for sale. I replaced the camshaft to lunati voodoo cam two years ago. When I replaced it the motor looked to have been freshly rebuilt. The motor has only been driven in and out of the garage and has very little time running on it. The cam was however broken in properly. It also has...

Does a car intake for a 5.7 work with a truck timing cover? thanks Bill