Search results for query: *

Hi guys I am installing a Holley sniper efi with Holley hyperspark ignition system on my 1975 Plymouth scamp with a 360. Holley says I need to hook up a certain wire to a switched 12v source (hot with key in ON position, and hot while cranking) and I cannot use the positive of the ignition...

1966 Dodge Monaco 2 Door, 383 big block 10:1 compression 325 horsepower 4barrel, 727 Torqueflite auto, power brakes, 8-3/4 rear end, A/C car for sale. 130,000 original miles. Car is all original. Clear Missouri title. Starts runs and drives great!! AM radio still works. Bench seat has a few...

For sale used 308 cast swirl port heads off a 1989 1-ton B350 ram van. Roughly 130,000 miles on them no cracks just one burnt exhaust valve. Smog ports plugged. Was using on my scamp 360 setup. Not sure of what reasonable asking price or what shipping would cost? I will post more pictures...

Right now my 1989 roller 360 is running stock heads( motor pulled from 1 ton ram van) which I believe are the 308 swirl port heads. Currently the motor has a eddy 650, single plane intake, hooker long tubes etc. I have a set of 587 Indy heads with the larger 2.02 valves, I am considering...

Currently riding a open 2.45 geared 8.25 rear end in my 75 scamp /360/727 I would like to put an A-body 8-3/4 under my care but do to being hard to find and or expensive I have been looking at other options. I understand I can move the spring perches of a B body 8-3/4 and with right offsets...

I have a 75 scamp with a 360 small block/727 torqued light and an 8 and 1/4 rear end. Correct drive shaft length suggestions would help a lot thanks!

Hi guys I got a jasper 383 big block with a Holley 750 carb with a weiand high rise dual plane intake/ an long tube headers. I put my car on the dyno and did just one pull. The car when accelerating seems to almost miss out or run a bit rougher from roughly 3,000-5,000 rpms. I don't know if it's...

Own a 1975 plymouth scamp with original rear axxle in it. The tag on the back of the pumpkin says 2.45 I'm assuming is the gear ratio. I was told the rear axle is a 8.25 or 8 1/4 axle does anyone know if that is correct or how I could find out ? I want to add some diff gears and some type of...

I got a 75 A-body that the door handle doesn't work on. I have the door apart because I am painting the car and the reason it doesn't work is because the little plastic clip/bushing things r broke the make the door operation work. Any ideas to where I can get some??? Thanks for the help

I'm installing a set of 002/003 super stock springs on my 75 scamp and I bought new u bolts grade 5 1/2"x3"x8" size. The car is for street purpose only and I'm not sure what to torque the u bolts down too. A guy told me 25 foot pounds is it so the rear axle can move. That doesn't seem right...

I recently purchased some "super stock" springs for my 75 scamp for the purpose of lifting a slightly sagging rear end and to replace the old ones. The numbers on the springs are the 002/003 "super stock" leaf springs which I am told is/was a popular leaf spring. I am wondering what the history...

What I have is a 1989 roller cam 360 (non-magnum) out of a 1-ton 1989 ram van. I put the motor in my 75' scamp with a few mods and was wondering roughly what power it should make. It runs an edelbrock 650 4brrl , edelbrock torquer 340 single plane intake, hooker long tube headers, and I believe...

I own a 1975 Plymouth scamp and have been looking everywhere for a hemi dart styled hood that would fit. If anyone has any info or a website that could help me would be greatly appreciated !! Thanks