Search results for query: *

I know its not a mopar but i had a bronco 2 that did the same thing with a 5spd trans. it would pull well up to 3 or 4k rpms then just go flat. Unknown mileage on the engine. I advanced the distributor and it picked up really well. It pulled great thru all gears and improved fuel mileage. The...

Thanks for the response. I will lay them side by side once I get them out.

I have a 74 Swinger and I also have a 66 Bronco that's rusted out. I've done some research and found that the 9in is less than an inch wider than the 8 3/4 for an a-body. I would have to do a pad flip for the springs and probably move them in some. My question is this, does it have the off...

Thanks Dartn440, I read your build and yours turned out great!!!!!

I took my Dart out for a spin since I siphoned out the fuel tank. I put about 20 miles on it and put about 7gal of pump gas in it. It ran very well and never missed a bit. Now Ive got to find out why my fuel gauge isn't working, but Ill still drive it though!!!!:cheers: Ive got a few gremlins to...

The FUMES are NOT TOXIC!!!!!!!!!! I REPEAT NOT TOXIC!!!!!!!!!! They are FLAMMABLE because its hydrogen gas. Think of the Hindinburg Blimp. Its just like charging a car battery, No open flames or smoking, and do it outside and don't put the lid on.

I used Arm and Hammer super washing soda. Got it at the dollar general

No its positive to the the annode and negative to the part. Always remember that positive attracts negative.

Here's my fence post and coat hanger wire connecting them all sorry they're all crooked.

This is my setup for electrolysis. This is the barrel and nonpainted fence post and battery charger

I use a roll around battery charger that goes up to 200 cranking amps. It has different settings from 10, 40, and start assist which is the 200amp setting. Ive tried it on 40 and it didn't do any better than at 10. I only use 10amp now. Yes, you are correct, it does seem to take forever but I...

Ok I will. Its a 50gal plastic degreaser barrel. It has 8 electrodes made from metal fence post. I drilled 1/4in holes near one end and made a hanger out of a........ wait for it.......... a metal coat hanger. Then I tied them together through the hole with a straightened coat hanger. It was...

After electrolysis and sprayed with a pressure washer

Before electrolosis

No I still have the rusty one. It should clean up well with a little turning. Just so long as there are no high spots. The black that's on the journals I believe is old grease that was put on it before storage but it comes right off with a wire wheel. When I took it apart all the bearings were...

And here's my new 340 crank from standard crankshaft.

Here it is after electrolysis and some wire wheelin.

Here's my crankshaft when I pulled it out of the shed

Well it looks like I spoke a little too soon!:oops: I was going to fill it up and it died!! Could barely keep it running long enough to turn around and head back down the hill. So I got it home and parked it for the night and calm down before I got to mad and aggravated.:angry5: After a good...

I guess I meant adjustable rocker arms.:oops:

Ive got a question that ive been pondering on that maybe yall know. Does anyone know the the difference between the rocker measurements on a /6 and LA small block? Reason I ask is that manual rocker arms, even cast iron are few and far between around my area. I was thinking if they are close...

It drives really, REALLY well. The drums all around actually work very well. It has power steering that is operating great. Trans shifts well and pulls strong with firm shifts. Ive got a 66 Bronco that doesn't have a straight panel on it that's going to donate its 9in rear with 4.11 gears. Maybe...

I bought the car from an old feller that had it under a tarp. A good buddy of mine turned me on to it so we got to talking and he sold it at a great price. He had shot at some crackheads trying to steal the gas but hit the car. Luckily he didn't hit the glass but told me to get it before...

Most small welders come with the regulator anyway to run gas if you want or not. I have a Hobart Handler 140 and I use Flux core wire in mine at.035 ga. One of the main reasons I prefer flux core is you can weld in a hurricane if you want. If you ever weld with gas and just so happens a puff of...

Chevy veiw

The pernt.

Here's another

I hope thes load ok. Its got all the slant six low power mess in it now but hopefully that will change as soon as funds allow. I've got a 72 340 that I plan on putting in once I get it rebuilt. I have more pics that I'm gonna put up. Thanks for checking it out!!!!

Im 10 miles from the Big Peach!!!!!

Ive gotten the Dart running but im gonna have to get a battery. Once I do that and clean it up Ill post some pics. By the way my names Tim and Im in upstate SC.