Search results for query: *

Lower control arms with new pivots. $200 plus the ride or pickup Lancaster pa

I have some 13/16 and one 5/8 hemi sparkplug t handles. Hemi spark plug t handle wrench | eBay. I have them listed on ebay but will sell direct to avoid the ebay fees. $25.00 plus shipping.

383 pushrods for solid lifters. 8.600 long. ball on one end cup on the other. They are from Mancini racing. Used for mock up. $132 new. $60.00 plus shipping.

I have new sway bar bushings and bump stops. Tie rod sleeves also included They are new in the box and have been sitting on my shelf for a few years. What you see is what you get. $60.00 plus shipping from Lancaster PA

Autometer pro control. I have had this for years. Was going to use this for nitrous control at one point. $25.00 plus shipping

10 inch drums and spindles. Upper small ball joint control arms. Brakes and drums look good. $60 obo. Would prefer pick up in lancaster PA

I am currently running a stock 5.2 magnum in a D150. Headers, Carb, Port matched. Just finished building a 318 with XE262 Cam. Stock 89 short block, port matched. Do you guys think the 318 with the XE262 cam will make more noticeable power compared to the stock 5.2?

Does anyone reproduce these clips. They are behind the rear interior trim at the back glass on a fastback. What other years use this? Thanks.

Milidon dual pickup external oil system. includes the plate thea goes between the oil pump and block, plate that goes on top of the oil pump for the filter, swinging oil pan pickup, hoses and caps incase you only use one pick up, and longer distributer drive shaft for a 383/400 block. You...

Moroso underdrive crank pulley. Bolts included. $40.00 plus the ride

I have a Sun 500 machine. I have heard there is a way to hook up a GM HEI module to do electronic distributers. Does it work and how is it done. I do have the LED kit from armount installed and it works awesome for doing points.

looking for a magnum intake for a carb. dual plane perfered. also may be intrested in magnum roller cam.

Blue sun visors 10.00 set of blue seat belts. two red seat belts included also. 20.00 two 67 window cranks 5.00 two blue defroster vents 15.00 Set of wire covers that go along the inside corner just inside the door $10.00 Ashtray 5.00 All plus shipping form mountville pa

SOLD two corners for the 67 style rear glass $5.00 plus the ride

$20.00 plus the ride

PENDING Set of 4 wheel well moldings. not bad shape but not perfect. $30.00 plus the ride or pickup in mountville pa

I have two of the vertical windshield trim pieces. 68-69 cuda. $30. Will ship from Lancaster pa

Wiper motor. Don’t know if it works. Been sitting in my garage for years. $20 sold wiper mechanism available also antenna from my cuda. $10 sold Parts are in Lancaster pa. Will ship on buyers expense

Left over stuff from my 67 barracuda fastback blue seat belts $30. Sold Blue sun visors. $20 Wire harness cover that goes along the inside corner of floor. $10 Defroster vents. $20 Door glass holder. $5 Pui fastback black headliner. $50 sold parts located in Lancaster pa. Will ship on buyers...

Nice fastback trunk lid. Only surface rust. Very solid. Will not ship. Pick up only. $350 obo. Lancaster pa

do I need to glue the glass into the gasket on the rear window? seems like it will fit nice and tight into the gasket once the lockstrip is placed in

anyone know where to find these little nylon things to attach the rear inside trim around the window on a fast back. Also do do you install the glass before you put the trim on?

I but the regulator back in but the glass doesn't go up and down correctly does anyone have any pictrues of one correctly assembled before putting it in the car or a picture of a regulator installed

looking for a good used 383 points distributer to use for break in on engine stand

bare housing for b body $50

741 case b body rear with backing plates. 741 has a clutch style limited slip a few gears on the ring are chipped off would need rebuilt $500

I have a complete 489 case open rear with brake backing plates and hardware fits 68 - 71 b body center section needs rebuilt $600

good 67 cuda wire harness $40 also have a dash insert that would need restored $40

2 uppers and 2 lowers needs pins $30 plus shipping

fender and trunk emblems $50