Search results for query: *

I have a 3.23:1 sure grip 7-1/4" rear end in my 66 Barracuda Formula S. My question is will I need to replace the carrier if I go to 3.55? Where is the break? Thanks.

I have a 66 Barracuda Formula S that was delivered 10-12-1965 according to the certicard. My question is do I have the 65 and earlier engine with the unique intake/ head angle bolts or the later. I would like to use a newer dual plane intake. Driver side casting # 2465330-4. Passenger side...

Hey guys I'm looking for a cater one bbl air cleaner stud/mount. Seems like they're getting harder to find.

Does anybody have a air cleaner mount/stud for a carter bbd one barrel? Seems like they're getting harder to find.

Can anyone tell me what wheels were available from the factory for a 1966 Barracuda Formula S? Some say the rallye wheel wasn't available until 67, some say 68. If they were available in 66 was it the same style or different, and what center would they be in 66? Obviously these are the sbp...

Hi Guys, I am trying to identify a block number on a 1966 barracuda. This is the number stamped on the block on the left side directly under the cylinder head. It appears as R 273-8-5. I have looked at several "decoders" and can't quite figure it out.

I've been thinking about replacing the demon carb on my 340 and going back to A thermoquad. Most of the ones I find are 800 cfm. Are these the ones that came with 340,s or were there smaller versions. I realize they have a small primary and large secondary (spreadbore) does this account for the...

I was discussing the shift points of my 727 in my 72 demon with my mechanic neighbor. He was saying that this was controlled by a combination of the modulator and linkage to the carb. There is no modulator on the trans but there is a plug on the right side rear, he said the modulator should be...

hi guys, selling my demon. 1972 orig a 318 car now has 1970 340. 8-3/4 3:55 sure grip 727. 8 yr old paint not perfect but looks good. ps, man brakes, subframe connectors. interior very nice. all rear suspension new. springs, hangers,bushings, all new up to the subframe. please pm me for pics. i...

hey guys, i need an emergency brake setup for my 72 demon. mostly i need the bracket underneath that attaches to the floor pan. when the previous owner replaced the floor plan they didnt put the bracket back. i do need everything to the rear cables. thanks.

hi guys, i am still looking for 65 dart hearter/ac controls. also need ash tray and radio. i would like to get these from 1 person/car, but not mandatory. please see pic, this will show what i need. please email to [email protected] am also looking for reasonable intake and carb...

i am looking for a sb intake and carb for a 318. two barrel or small 4 barrel, preferably something i can bolt on, im not good with carbs.

i need heater /ac controls for my 65 dart. that, radio and ash tray are all that is missing. i have located the other items, but really need controls. someone apparently robbed them b4 i got the car. i found a whole car with what i need and much more but is in ok., the owner wont part it out...

i am looking for heater controls for my 65 dart. it has factory ac (i think). i dont know what they look like, and if this one has ac controls with heater controls. i am missing the whole section, radio,ash tray,ect.i have seen some pics on ebay and others, but am still unclear on heater/ac...

Does Anybody Have A Picture Of What The Air Cleaner Looks Like For The 70 - 72 Dart Demon With Dual Scoop Looks Like? I Have A Demon With Scoops, Holes In The Hood And The Rubber Grommets In Place, But Dont Know What The Factory Air Cleaner Looks Like...

i just got some moser 9400m bearings from summit. when i go to this sealed bearing, do i leave out the inner seals? people have told me this, that the diff fluid lubes the bearings. it makes sense because there are o rings on the bearings.

could anyone tell me the correct measurement for an a body 8-3/4, outside to outside of the flange on the housing. i get conflicting answers, mostly because i dont think people understand the question. i supposedly have an 8-3/4 1 '' narrower than stock, 1/2" on either side. this is for my 1972...

Can Someone Enlighten Me On The Differences On 8 3/4 Cases.years,interchangability If Any,strenghts,weaknesses,advantages,disadvantages,spline Counts,availability Issues.also What Is A Cone Type Posi.as A Rock Crawler I Am Familiar With Spools And Lockers Of All Varities,and Understand Clutch...

My Friend Just Purchased A 66 Barracuda With A 6 Cyl And 3 On The Tree.the Trans Needs Rebuilding/replacing.can Anyone Tell Which Trans This Might Be,and Maybe Some Parts Sourcing?this is a manual trans.

i recently aquired this car in a foreclosure.it is a very straight car,excellent glass,all the trim is there and good.the car has been sitting 10+ years.the interior is rough,no headliner.this is a gt with the factory floor shift.it is a 273-2bbl.much to my horror i discovered the block was...

i grew up with some older neighbor kids who were a body fanatics.340 gts,a body cuda,273 dart,340 duster and more.while other kids were playing ball at 12 years old i was wrenching for free-just for experience.i guess i came to like the underdog factor of the sb mopar,in an area seeming to be...

i have a column shifted automatic (1972 340 demon) that is now floor shifted.i would like to clean it up,add a tach to the column ,ect.i would like to change to a manual shift column or modify the exsisting column.any suggestions would be helpful.i finally have another a body after 25 years without.