Search results for query: *

Guys looking for factory fuel pump to carb fuel line pics with a t-quad 72/73 anyone post some please

Do they make a block off plate to eliminate the air tube at the rear of the manifolds, wanting to eliminate the air tube on my 318 manifolds.

Are there any aftermarket or repop trim rings out there that actually fit the rally wheels??

Looking for a 73 340 intake or a 74 and up 4bbl 360 intake anyone? Thanks

Looking for oem 8.25/8.75 axle u bolts with the flat top anyone have even 1?

Have a set of stock 1.88/1.60 valves and springs from a 915 j head looking for the stock retainers and the keepers anyone have a used set before I look for new??

Looking for a Mopar performance fan and clutch assy or something similar good used. In my 77 volare roadrunner 318 no AC

70-72 318 2bbl intake looking for the choke well cup and choke if you have that too thanks

Anyone make a thin head gasket for a standard bore 318?

Looking for a set of 302 casting small block heads anyone? Thanks damn auto correct casino wth of course supposed to be casting

Looking for a valve body with a shift kit installed for my 77 904 anyone have one or can do one up for me?? Thanks. Brett

Looking for a small block 2bbl non EGR intake t manifold

Looking for a set of 1.88 and 1.60 valves and a set of springs anyone?? Used in good condition

Looking for pics of the fuel line routing for a 72 t-quad from carb to pump thanks

Looking for a t-quad intake for a project build anyone? Pm me thanks. Brett

Looking for a 22" V8 radiator fan shroud anyone have one?

Cragar s/s 15x10 with new Mickey Thompson S/R 28x12-15 tires 4 1/2 bs unilug pattern taking to Carlisle with me spaces M58-60 asking $400 for the pair

Looking for a pair or 4 small bolt rallye wheels anyone?

Anyone have 4 they could spare mine are mia in the dash it is for a 70 Dart standard dash thanks

70 Dart small block new heater hose nipple new gates hose and new spring clamps kit from Layson's the clamps for the 1/2 hose are to big can slide them right on the hose with your fingers with very little resistance they are red in color tried a different manufacturer hose same issue are there...

Guys I need the correct kickdown linkage for my 70 Dart 340 727 trans anyone have a complete set up or just the adjustable rod from the swivel on the intake down to the trans should be 13 1/4 to 13 1/2 inches long as I am told by a very helpful member anyone?? Thanks, here is a pic of what I...

70 Dart 340 using an ld340 intake ordered a repop nipple 1/2 hose what size is the threads? My intake has 3/8 npt have a feeling the nipple is going to be smaller anyone know??

Looking for the upper horn low note with bracket and attaching bolt mine is missing thanks

Looking for a ground strap from firewall to head for a 70 340 anyone?

Now I know this is not how you measure the front end on our cars just trying to get a temporary base line anyone with a 70 Dart could you measure from the ground to the wheel opening on the front please thanks

So my Darts front armrest were showing some typical wear just looked crappy so I ordered a set from Laysons wtf over an hour to switch two armrests holy hell what a pita they are not an exact copy of the originals a tad to thick the screws needed to be a half inch longer to work with the repop...

Guys need help again seems I have a hodge podge of linkage on my Dart 70 340 727 of course anyone have a set up they can part with? Mainly need the parts up top rod and linkage at trans is ok throttle pressure/kick down rod is cobbed and the bracket that bolts to the intake anyone? Thanks. Brett

Guys how far are they supposed to stick out from the valance? The ones in my car are rusty and stick way out there, I ordered a set from Accurate just holding them up to what is there now they set back a little but man seems like they really hang out there here is a pic of what they look like now

Looking for a dual plane intake performer rpm, ld340 anyone have one they want to part with??

Looking for a tuff wheel retainer and horn switch with the mounting screws a plus anyone? Thanks. Brett