Search results for query: *

Went with a 408 Stroker and sadly need to sell my 340. $5000 very firm. LOCAL PICKUP ONLY (Los Gatos, California) Mopar 1973 340 motor Engine casting number 2780930-340-1 Original exhaust maniforlds Original valve covers Original intake manifold Air Cleaner and "Pie Tin" Also included-...

Using the complete Holley setup. Hyperspark, coil, distributor and ignition box. Can I just twist IGN 1 and IGN 2 together? A relay would be in an "OR" configuration, right? We really appreciate the help. This has been a big project over a couple years. I think we're one wire from getting it...

Hey! We need 12v power on "on" and have it continue on "start". A constant 12v through the start cycle. I can't see how we get both out of the ignition switch. We're setting up a Holley Sniper EFI on a 408 stroker in our '73 Duster. Checked the FSM, but am not seeing it if it's there...

Definitely! Much rather have you guys snicker…. . Thanks for all the help!

Not the first dumb mover on this build and definitely not the last! Thanks everybody (he says slightly embarrassed).

Yup. Looking at it now makes sense. But it did come from Griffin with the petcock on the other side..... Still our error. Water didn't come out of the dipstick, we pulled the entire dipstick tube out of the trans and water/fluid came out of the hole. Engine never spun. We poured a bunch of...

Operator error is a constant around our shop... There is a petcock on the other side of the trans that I assumed was the drain. There are two 5/16 nipples side by side on the side where the trans cooler lines come out of the trans. That's what we used.

Appreciate all the help . It is what it is, have to move forward and get this beast on the road. Ordered it as AT directly from Griffin and these bungs look pretty AT to me...

Sounds like we need to get it running ASAP and keep feeding AT fluid through it.

I can't believe that Griffin didn't pressure test this. Water poured in the top of the radiator doesn't even slow down on its way out of the AT cooler fittings.

Just distilled water, no anti freeze. We were hoping to get it started today before this debacle.

Thanks. Dumping the fluid/water out of the pan. What about the rest of the internals? Anything to do about that?

We have a 727 in our 1973 Duster. Got a Griffin radiator with an AT cooler connected to the 727. We don't have fuel or spark set up yet, but bumped (not even a full revolution) a few times as we got the starter, etc. hooked up. We were then working on the trans dipstick and when we pulled it...

Perfect! Thanks for the advice, much appreciated.

Did they come with mounting brackets? I've been looking and couldn't find a "kit" with all the components. I'm just trying to use it on my Duster trunk so should be much less of a job. Any thoughts?

I’ll keep everyone posted, but I did some basic math and can’t see how not to do a crate motor when time is critical. I want to make sure my boy gets a chance to do some work himself and Blueprint has us dialed in. I have a 360 block in the shop that we will build later, but getting the Duster...

He's paying his share. After 50 I think we all get the “restrictor plate”. :)

I've tried the testosterone restrictor plate. No luck... Have to stick with backing the HP down for now.

Thanks for the advice guys, much appreciated. Got hold of Johnny Mac at blueprint and ordered a 408 stroker with a Holley Sniper EFI. I’ll let you know my experience when I get the motor, but the help we’ve received was phenomenal. Talked to other vendors that sounded like they were doing me a...

Just sent you a note!

Better than playing video games like his buddies....

Not trying to co-op the thread. Sorry about that. Just trying to figure this out. Oddly enough, this is for my boys Duster build, so I'm trying to keep the HP under control, thus the interest in the 360. I'll call Johnny at BP.

Has anyone had experience with crate motors from Tristar out of Wisconsin? I'm talking to them about a 350 HP 360 cuin. setup. Seem like pretty smart guys, but I'm not sure about their Mopar experience.

Many people wouldn't appreciate the utilization of the winch on the quad in conjunction with the cherry picker.

Engine out, trim off. On the way to the body shop.

Need someone that want's to trade....

Thanks!

I have an ebody 8 3/4 rear end that is 3" wider than my duster 7 1/4 rear end that I'd like to swap. If I move the shackles in to fit, I'd have the big bolt pattern and an 8 3/4 in the Duster and only be adding 1.5" to the width on each side..... There must be something wrong with this...

Thanks! Much appreciated. Working on it now...

1970 Barracuda Gran Coupe-318. Maroon with a black vinyl hood and 2.73's in the rear end, Drive at pretty high speed all day. Great cruiser. Girlfriend stuck it in a tree. She was quickly my ex-girlfriend.