Search results for query: *

When I turn the ignition switch to start position I just get a click out of the starter relay. I can get the engine to turn over if I Jump the relay. My question: Is the relay good if it clicks when key is turned to start position? Maybe my neutral safty switch is out of adjustment. What...

Got the Dart on the road now. Couple things to finish yet, but I had to drive it befor Winter sets in. Here a couple pictures. Enjoy.

Can anyone tell me if I can take the gas gauge sending unit out of the gas tank without removing the tank from the car. The car in question is a 68 Dodge Dart. Thanks for any help. Gary

I need 3 retaining clips like the one pictured (sorry for poor quality picture). These are the clips used to hold the heater-defroster cables from the heater-defroster control to the heater box. Anyone who might have 3 they are willing to sell, please email me at [email protected] Thank you. Gary

Some time back I seen a post I think was from a member here about a fan clutch and fan that would help with a clearance issue for a 68 Dart or some other A body car. Need more clearance between the fan and radiator. I'm thinking the member was 70Duster440. The member posted the part number...

I want to replace the old windshield wiper motor assembly in my 68 Dart with something that takes up a little less room around the distributor. I installed a MSD e-curve distributor and the plug wire terminals are only about 1/2" away from the wiper motor assembly. When I install the plug wire...

I installed the engine and transmission this weekend. First one I did from bottom up. Easiest install I ever did. Not one scratch. Didn't take and hour.

Notched the K member for my 68 Dart. Now have plenty of room for the Milodon oil pan.

Installing new torsion bars in my 68 Dart. I know there is a right and left torsion bar, but does it make a differance which end goes to the front control arm or the rear cross member?

Has anyone installed their small block engine and transmission in an A body from the bottom up? Any sugestions or pictures would help. Thanks.

Hey guys. Thinking about installing my small block in my 68 Dart from the bottom. I have the K member out now as I am notching it for oil pan clearance. I thought as long as it was out I would be better off installing the engine and transmission as a unit by lifting the car and lowering it over...

Got the Dart home from the paint shop. Looks great. Now I can install the 414 cu.in. small block and the rest of the project is well under way.

Went by my painter today to look at the Dart. It is red. Picture doesn't really show the true red color, but believe me it is really red. Looks very nice. Can't wait until I get it all back together.

I got my tti headers today. I had to put them on the engine to see what they would look like.

I'm trying to put together a 408 stroker moror. The block I'm using (a 360 magnum block) doesn't have any holes in the front on the deck for water to get from the block to the intake manifold and back to the radiator. Can anyone tell me if I can simply drill the holes in the block where they...

Thought I would share some pictures of my 414 stroker motor going together.

Thanks for the information to those who replyed to my question about mounting bucket seats in place of a bench seat.

I have a pair of bucket seats from a 68 Dart that I want to install in my 68 Dart that has a bench seat. Can anyone tell me if the outside track on the bucket seat will bolt directly into the mounting holes that are on the floor that the bench seat was mounted to? And do I have to make a mount...

Help!!! In a 360 magnum engine, does the spider that holds the hydraulic roller alignment yokes in place have a washer or short spacer between the spider and the block? Or does it just bolt directly to the 3 bosses in the block? Anyone have the answer for me? Thanks for any help.

I didn't fall off the face of the earth. I do check the site almost every day. Just thought I would share the latest part of my Dart project. With the help of a very talented friend we made this dash insert for my 68 Dart. Believe me, it was a lot of work. I have to paint the dash black and...

Rat Rod here, I need to have the rear bumper for my 68 Dart straightened and rechromed. Anyone have any suggestions as to where to go to get this done. Any input would be greatly appreciated. Thank you.

I think I have it figured out now. This is a picture of my 76 Dodge Colt with a Hemi that I raced for 8 years. I had a lot of fun with this car.

A friend of mine in California found a 68 Dart for me. I had the car shipped to me in Wisconsin and started to rework it the way I would like it. So far I removed the 7 1/4 rearend and narrowed a 8 3/4, installed Moser axels, a posi unit and 3.23 gears and moved the rear springs in. Then I...

Hi everybody, My name is Gary. Just hooked up with this site. Everthing is pretty new to me, but I will try fit in. I'm from Northeastern Wisconsin. I am an old retired drag racer. Did that for a long time. Over the years I had several different drag cars. Started with a 56 Chevy, then a...