Search results for query: *

Took the Duster to our local show, had about 150 cars. Got 1st place in the 1971 to 1980 modified class. There was a Dodge street wedge gussied up like a Maxie that was nicer by a mile than mine, and i even voted for.

After the last couple of years our track should run a full season. Arroyo Seca in S. NM off I-10. It is why I built my car. Cant wait.

I cross posted on FBBO. Ebay ball joints wont fit the socket for the uppers. Reverse engineered in China I am sure, but what is not? Got my $$ back and got some from Oreillys. Checked NAPA and offshore also. Our choices are getting slim.

Lift is in working well. Next is a roll up door. My back is going to thank Me.

Price reduced to $650. I went through this and added a Sure grip. 3.21 with new bearings and seals. New shoes wheel cyls lines and hose. E-brake cables complete drum to drum. I did not want to kill it behind a Big Block went 8 3/4. Will not ship. Located in Deming NM. Dusty from sitting

Just pulled Going 8 3/4 Complete diff drum to drum. 3.21s with Suregrip. New brakes with spring kits shoes and wheel cyls. $850 or reasonable offer. Located in Deming NM. No ship...

Can anyone show a pic of the plug and wires to the circuit board plug and color codes? Thanks

Looking for cruisin gears any # case

Where can I get /6 engine parts like water,fuel pumps. Head bolts , gasket set ect. All the local chain stores like NAPA Oreilleys ect have no listings. For a 73 225. thanks.

Things are coming together quickly. Still a few tid bits like a turn signal sw accel cable ect. I had fits with the inst panel harness going from a hacked up A/C set up. I had one from my donor no A/C Slant 6 auto so I swapped it in and bingo Most gauges and lites work sans brake lites. Got a...

Hello All, couple of questions. I just got a new tank and sender for My 73 Duster and they are identical to what I pulled off. Q1 is the filler cap vented or not? I would think it is a sealed cap what with emissions of the period. Q2 the tank has 1 nipple and the sender has the 2, 1 for supply...

I am going to order a drive shaft and have a question on the rear joint. Summit has a deal from Moser I think, it will include a 3in Cromolly withe the front yoke and 1350 joint. I have a shaft that came with the car so I knocked one of the joints out to see if it fits the rear yoke and it dose...

New trans and converter are in starter and some wiring next. The fender wells hang a Wee bit low but when I get it back on the ground I think some heat and a jack will get them up. I will have to notch the T Bar outer support to run an exhaust, then fab it back together. Will get some pics as...

Trying to get the cable hooked up but seems way to long. I think it is original to the car that was a slant 6. Low deck 400 with a Weiand dual plane, Holley and a 1 inch spacer. The bracket is to short for a good angle also, Looks like the one I have on my 68 R/R. What are you guys using? Will I...

Putting a 440 in a 73 Duster with Hooker super comps fender wells. Looking for a recomend on tire size. Going with slotted mags all around and the fronts will be 15X7. I know it will be tight but what can fit? was looking at some Cooper 215-60s. I have some 14X7 but it is a no go with caliper...

Posted this last month. 73 duster roller, no interior. Nice floors, trunk, quarters. Decent fenders, doors. BBP front discs, 7 1/4 rear. Located in Eugene Or. $800 PM Me a # and will send pics.

Got a 8 1/4 complete from the junkyard with 3.55s and a LSD case out of a 93 Dakota. All looks nice, new bearings,seals ect installed using the 321 original gears. Installing the carrier and find it hits the case on the right side by top cap bolt. Looking at the Dakota housing it has been...

Just like it says. for 3.21 gears 27 spline. PM me and we can choot the chit. Located in Oregon closer the better.

Anyone use the Milodon deep pan 31010 in the 73 A-body with a Big block? How far dose it hang down below the K member? Says it has a 7 3/4 deep sump. Ok for street?

Got a 8.25 out of a 73 Dart Sport 340 going in my 73 Duster. Got it stripped down to blast and powder coat. Figured I might as well freshen it with bearings seals ect. I want to get rid of the crush sleeve with a solid shimmed spacer. Looked on Ratech and their # is 4114 for the spacer kit. They...

73 Duster Roller was a 6 cyl auto. Pretty much a bare shell with doors, fenders, hood,deck lid and glass. Body is pretty much rust free, nice quaters floor and trunk pan. Nice roof and window channels. Some trim like grill headlite bezels tail lamps. Has cluster a PS column with a manual box so...

Howdy from Oregon. Jumped over from FBBO as I just got a 73 Duster. Looking foward to conversing and pickin your brains. Pics to come so dont beat Me up yet. Plans are for a b 400 727 8 3/4 fender well Hookers and maybe a 871 w/2 4s.